Discussion Locked

Can Not Get XP to install on a new compu

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have built my first computer and have tried to install XP on it [yes, it is a legal copy]. The computer has a DVD drive that is set to master and is on the end of the ribbon cable.The BIOS detects the DVD drive and it is set first in the boot order. The DVD light comes on when the computer boots up and when the cd is inserted into the drive, the drive sounds like it is spinning but I get an error saying the boot disk was not found and to check the cables. I have checked the cables several times.
Is there anything I may have forgotten?

Thanks.

Norm

10 replies

by thechas

Is the DVD drive jumper set to master?

Is the DVD drive properly detected by the BIOS?

Is the DVD drive on the Primary Master?
Or on the secondary Master?
It should be on the Secondary cable and your hard drive should be the Primary Master drive.

It is possible that your DVD drive either has a problem, or cannot function as a CD-ROM boot drive.

Do you have a "standard" CD-ROM drive that you can try?

Another option would be to download the correct startup disk file from Microsoft and create the floppy boot disk set for your version of XP.

Chas

by rewrite

Have you tried booting with any other bootable cd's to test? If you can boot with a different cd then your xp cd is bad.

Cheers.

RW

by willcomp

Download and extract XP Setup Disk (single disk) from link below.

http://freepctech.com/pc/002/files010.shtml

Then try to install XP from CD using setup disk.

If no success and you used 80 wire cable to connect DVD drive, ensure that blue, red, green, or similar connector is connected to mobo and black connector is connected to DVD drive.

I've had problems booting from DVD drives at times even though the drives were functional.

Rate this answer and post back with results if you need more assistance.

Dalton

by willcomp

If HDD is SATA, set DVD drive as master on secondary IDE channel. Really shouldn't matter if it is on primary channel, but doesn't hurt to be safe.

by rindi1

The windows XP boot CD asks you to press a key to boot from it. If you miss pressing that key the system will try to boot from HD and the message you got above would be displayed. Some systems tend to boot up too fast for the display to turn on in time, so it could be possible you don't see the message. You could either try to continuosly press any key as long as you don't see anything on the screen, or you could get the system to do a thorough memory power up test (Will take longer to boot, but will also turn on your display in time).

by daowen

Norm:

I think the answer is closer then you think. Look in the bios and set the first boot device to be the CD Rom. Make sure that the XP disk is in the drive then boot the system. You should get a message asking to hit any key to boot from the CD. Hit any key and you should be able to start the install.

Doug

by daowen

Norm:

There is also maybe another answer pending on your bios. Move the DVD to IDE 0 and set it as the slave.

Possible that your bios is not looking on the IDE 1 for the CD to boot.

Doug

by sgt_shultz

these are ide devices, not scsi, yes?
maybe you have a cable select ide cable? is it labled 'master' 'slave' next to the connectors. that is a for sure giveaway that you need to have the jumpers set on your devices for 'cs' (cable select)
watch the black screen during boot. your bios will check the ide bus for devices. it should briefly show them when it finds them. other way to check cabling is to go into bios, see if you can force ide detection. if it fails to find the devices you still have something not cabled or jumpered right. inspect cable for damage. recheck jumpers. try another cable. inspect drive for connector damage.
if drive lights never go out on dvd, you have cable on 180 degrees off ('backwards')

by rapell

I think your DVD does not support CD_ROMs. Why don't you try using a normal CD drive and see what happens? I think what you are doing is like trying to play a music CD on playstationII. This is a Data CD. Check it out.

by acegolfr

Did you load the proper cd/dvd drivers?
Try booting from a win 98 bootable disket from the a: drive load the drivers needed and select boot from the CD drive

This discussion is closed to new replies.