Discussion Locked

Can't change MTU...

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have been trying over the last couple of months to change my MTU to 1500 as instructed by www.broadbandreports.com. I have DrTCP and TCP Optimizer, both display that my MTU is at 1500, although on all tests I have performed I get the results that my MTU is set at 1490. To the best of my knowledge I am not using a Router, or FireWall. What is the deal with that? Here is my connection...Cabble Modem>10Mbps Ethernet Hub>another 10Mbps Ethernet Hub>My PC. The reason for the 2 Hubs is I have 2 PC's using the same modem and I don't have a Cat cable long enough to reach one PC so that I can use only 1 Hub. I have a Realtek RTL8139/810x Family Fast Ethernet NIC. The cable modem is a Mototola SB5100 SURFboard Cable Modem. Connection is 64kbps advertised. Cables are CAT 5 and 10. Input please !!!!!!!

8 replies

by cg it

hummm how to explain this? The maximum transfer unit MTU [packet size]is the largest size packet a network can handle. Now networks and subnets are established via routers. If a router encounters a packet to big for it, it fragments the packet, repackages it and sends it on its way to the destination. If the packet encounters another router that can not handle that size packet, the router will further fragment the packet, package it up and send it on its way. The fragments are not reassembled until the final destination is reached. Now, when you connect to your cable modem without the benefit of a router in between to establish your own subnet, your at the mercy of the ISPs network parameters. [in essence your computer is a host on your ISPs very very large network which may consist of very few networks and very LARGE # of hosts. [Class A IP addresses]Your MTU will be that that network can handle. If you put a router in between your cable modem and your computer, you've created a subnet and if that router can handle a packet size of 1500 then your MTU will be 1500. Your router will then fragment that 1500 packet to a 1492 packet plus whats left over, repackage and send it on it's way [because that is the largest size packet that network segment [between your routers WAN connection and your ISP]. Now the data stream and the amount of data in which you can receive RWIN or receive window is regulated by ICMP squelch packets [again behind the scenes stuff] your computer will accept as much data as it can and when it gets overloaded with send out a ICMP squelch packet to the sender basically saying "slow down" which the sender does but then will start to slowly increase the data flow until it again receives a squelch packet.

by cg it

hope that helps you understand what MTU or maximum transfer unit [packet size] is and does and what your RWIN [receive window]data flow and the ICPM squelch packet does for data transfer rates. Futher you may be at the mercy of bandwidth trottling which will only allow a certain amount of data to pass through regardless of your machine settings and ability to handle data flow.

by cg it

note: routers talk to each other and exchange data e.g routing tables and the lot. RIP or routing information protocol is the means in which routers exchange information . DVP or dynamic vector protocol does what RIP does but without the largeness of overhead.

by cyberghost_1

I was informed that I can change the ICPM settings. Is that accurate? What would be blocking me from being pinged?

by cg it

well ICMP protocol or Internet Control Message Protocol is used to quote.."for sending error messages, performing diagnostics and controlling the flow of data". unpingable means that the ICMP "ping" is blocked by a firewall or other forms of security devices which does not allow the ping packet to pass beyond it. the Source-quench [squelch] packet is used to tell the host to slow down the data flow. Now ISPs throttle bandwidth effectively controlling the amount of data you can send or receive. [only so much water you can send through the pipe] [only so much water you can draw from the pipe]. nothing you can do about it. Those tools you use only tweek your existing settings to find the optimal settings based upon the network your on by sending you some packets and seeing what comes back, how long it takes to get back. from there a suggested setting are made and you can apply them. your NIC card can only accept so much data e.g. 100 mbps or 10mbps just as your computer can accept and process only so much data. If those thresholds are exceeded you'll start losing packets or get errors in the data sent. Since TCP/IP is a quarenteed delivery system, lost packets have to be r-erequested from the source which adds to traffic and slows down the data flow [CRC error correction]. Hense the source-quench packet which tells the source to slow down instead of losing packets along the way and re-requesting them

This discussion is closed to new replies.