Discussion Locked

changinging motherboards

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
i just replaced my motherboard. everything else is the same. but i can't boot up. will my hard drive continue to function with the new motherboard without my having to do anything else? i thought all i had to do was change boards and power up and i would be ready to go. what should i do right after i finish making all the connections and power up?

11 replies

by mrafrohead

Did you format the hard drive??? Or is this hard drive still using the files that you used before???

by theoham

i'm using the same files, and no i did not format. but i think i know whats wrong: before i changed motherboards, the drive that went bad was set up as a slave, and now i want to use it as a master. the problem is while a slave it did not have a boot partition on it(according to a friend) therefore when i try to use it as a master, i can't because it's not set up to be botted as a master. is this right?

by mrafrohead

Sounds about right to me...

What kind of files are on the drive?? Are there OS files on the drive or just stored data???

If it's just stored data, you can boot your pc into dos and then move all of the files on the drive into a newly created folder. Then from there, install an OS and you should be good to move the files in your new folder to wherever you would like them to be...

Let me know if this works for you;)

mrafrohead

by theoham

i had Win2K on it, but it was a seperate hard drive set up as a secondary master. So i guess i can't use your idea. i was dual booting with ME and Win2K. Now i want to run this HD as the primary master on this new MB without having to format it. CanI? If so, how?

by techinca

From the sound of this discussion, you should be OK. You definitely need to adjust the HDD so it is set up as the new master. If you already have W2k on it, then you also have a bootable OS. It does not matter if you only used this drive as a secondary slave.

So let's see, you just installed the new board. Hmmm...here's another thought. Is the HDD type compatible with the new board? Meaning, Ultra ATA 66/100, etc. IDE/SCSI interface? If all this is the same (and you're sure), thenby simply changing the settings to make this your new master should do the trick.

by mrafrohead

With Windoze 2000 on there, you may need to boot with the CD and use your Emergency Repair Disk and have it reconfigure your boot sector so that Windoze 2000 is recognized on the drive...

It sounds like you were dual booting before and basically what happened, is you removed your boot partition...

If you run the ERD that will repair that and once you boot into Windoze you can edit it to remove the old OS that you are no longer using...

Also, don't forget to upgrade those Mother Board drivers...

To do that you need to uninstall the existing drivers and make sure that the Microsoft drivers are the ones that are loaded...

Once they are, then you can upgrade to your new drivers...

This all, of course, is dependant on whether or not you can boot into your OS...

One thing to remember though. Since you have a new motherboard, Windoze may recognize it and have a problem running due to the fact that the drivers required for the mobo are going to be different. Should thishappen, what you are going to need to do is uninstall the old drivers AFTER you put the hard drive back in your OLD computer. Once that has been done, you should be able to put it back into your new computer. This of course, only matters if the OSwon't load...

And finally, this is just my personal recommendation. Backup your personal stuff that you need, and format that hard drive and do a fresh install of Windoze 2000. That way you have a good install of the OS that is SPECIFIC to yournew mother board and you will get all of the performance and benefits out of it that you wanted and will come to expect...

Just some advice;)

mrafrohead

by lordinfidel

Before you go and start switching your drives around.

You will need to edit what is called the ARC name for your drives.

What is an ARC name? ARC (Advanced RISC computing) maps the path to the system files which are stored on physical disks then partitions.

The ARC name is stored in the BOOT.ini file on NT based systems. (Also used by unix systems, but beyond the scope of this).

Essenitally, in your BOOT.ini file on your 2K HDD, you should have multiple selections for OS. (ME, 2K) each with a different ARC name.

If you just swap out HDD's, the BOOT.ini entries remain, the startup menu will direct you to select an OS, but where it points to will no longer be valid.

This is all because of ARC.

For more info on ARC namesgo here:
http://support.microsoft.com/default.aspx?scid=kb;EN-US;q102873

(no spaces)

by nburke

At the risk of being too obvious?

Win2k does generate a sid..so changing the motherboard may well have confused the system..

If it's not even booting sounds like the jumpers for the cpu aren't set correctly? or if your lucky the board has an autodetect cpu feature which may need setting up in the bios.

As I understand "dual boots" in order for them to work with win 2k you need to instaall each in the same directory, and insure that you haven't set the win2k drive as an ntfs drive! otherwise ME would never read the drive!

Let me know!

Regards

by microbuff

Ok,

When you swap out a motherboard there afew things you need to do. I would suggest the below checklist:

1.) Connect all cables ( Floppy, IDE cables the same way you did in the orginal motherboard.
2.) Reset the CMOS jumper
3.) Autodetect the hard drive
4.) Reboot the system

* Note many times you may have to clear CMOS settings. Sometimes computers don't perform like are designed to. I replaced many motherboards and the above always works for me.

by gshollingsworth

I am going to combine a couple of previous suggestions. I don't think you properly prepared and went to far, it's not to late. Backup to where you started, then backup your data. Put your old computer back together to do the backup. I think you mentioned that there was a bad hard drive? This is what I am assuming you had: Dual boot WinME & Win2K, WinME on Master IDE, Win2K on Slave IDE, (Master IDE drive containing WinME went bad?), BIOS setup configured for autodetect HDD parameters. If this is the case you will need to make the Slave the Master and leave the bad drive out (for now). Boot with your Win2K CD and choose repair, then emergency repair, then manual repair, deselect verify system files and continue. Do not use an Emergency Repair Disk (ERD) in this case. This should get you a bootable Windows 2000 machine. Make an ERD now. Open Device Manager and uninstall everything found under System Devices, Computer, IDE ATA/ATAPI controllers, and Display Adapters if built-in to MB, then shutdown (do not reboot if asked). Restart system and go into the BIOS setup. Write down the number of cylinders, heads, and sectors that are being auto detected, and the PIO, DMA, and addressing modes (LBA, Large, etc.) Power down and put your new computer together, go slow, be careful, avoid static. When you powerup the first time go into BIOS setup and check that the parameters for autodetect match and the mode settings are the same. Reboot. There should be alot of new devices found to replace all those uninstalled. This should load appropriate drivers for the new motherboard. If things don't follow this pattern, stop and post back here. Somebody will be able to help you. Good luck and happy holidays.

by lordinfidel

(This is based on the assumption that all devices are connected and detected in BIOS, and that the OS will not boot/function)

Changing a MotherBoard, as the title implies, is not as simple as one would think.

And why is this not as simple as changing out a piece of memory or adding a harddrive or zip drive?

Think of your motherboard as the heart and soul of your computer. It is the foundation that your OS is built on.

When you install an OS, it adapts itself to the settings that the MB is giving it. (ie irq's, dma's, pci steering etc.)

Replace the motherboard without preparing the OS (which is an oxymoron and iffy at best) will have un-wanted results. As in boot failures.

Best Practices always says to first make a backup of your system data/files.
Install the MB, set-up the bios, and reinstall the OS and all programs, then restore your data. This will insure the best outcome possible for your system.

The other option is to again backup, but instead of installing a new OS. Remove the majority of drivers (do not reboot after each one), Once the majority of the big drivers are removed, like video, modem, nic, etc). Shutdown the system. Install the new MB, set-up the bios, and reboot.

Your devices should be found along with MB resources. You may need to run an installation that came with your MB.

But again, Best Practice is to always reinstall when you have a major change to the OS, ie (MB change, OS version change)

This discussion is closed to new replies.