Discussion Locked

Checksum error

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

The System: ALbatron KM18G Pro M/B BIOS date 2/24/2004
512mb DDR (FSB 333)
802GB Western Digital HDD (new)

The Problem: When attempting to install windows onto the new HDD it stopped at the point of; Setup is starting windows.
It would not continue past this point. I have tried different windows disks, same problem. I tried to enter the BIOS to see if there may be something not set correctly. I noticed at first that the date and time was all wrong. I tried to change it .. again to the correct time but it will not adjust further than February 2 2002. Any attempt to clear the CMOS sets the clock to January 1 2040 and trhe time reads as 2 2 2 and cannot be changed. Rebooting results in checksum error. No post beeps either, even after removing the ram completely.

The resolution: ? Any ideas? Possible BIOS virus?

21 replies

by mikex

Hi possible BIOS (Cmoss) Virus - check up first with a clean boot diskette/CD if it's clean go to your motherboard manifacturer site and download BIOS updates (or you can try with old working one) and Update your BIOS - this must resolve the problem

by daz'n'ash

Thank you for trying to help. Unfortunately after trying to flash the BIOs, although it said it was successful, it quickly became apparent that it didn't change anything.

by willcomp

Most of the times that Windows install quits when starting Windows, it is a memory issue. This is first time that extended memory is used in the setup process.

Swap memory or boot from single stick using each stick in sequence if you have 2 or more sticks.

BIOS problem is strange, but I would change to known good RAM first and see if that resolves problem. If not, then flash BIOS.

by thechas

Which version of Windows?

Windows 95, 98, and Me can have numerous problems including installation failures with more than 511MB of system RAM.

For "strange" BIOS problems, the culprit is often a case or CPU fan that generates too much electrical noise.
Try connecting case fans directly to the power supply, and if needed, change the CPU fan.

Chas

by jailbreak_pt

Hi

Have you update your board bios??
If so, see if you update with the right firmware and right model and version.

First: If not. Try to load-faild settings default from the bios menu.
Second: If the first did not correct the problem maybe your battery is off. Try to put a new one and in the bios take the default setup settings.
Save and exit.

Say that this correct your problem

Any help just asks

by daz'n'ash

Hi Chas, the attempted install was Windows 2000. Then attempted WinXP Pro. Same problem with both. It is a single stick of 512mb DDR 333 I am using. The mobo is new straight out of the box as is the AMD 2500+ CPU on it.

by otl

There are six BIOS updates which may fix your problem;

http://www.albatron.com.tw/english/service/bios_search.asp?keywords=KM18G+Pro+

Good article on the specs (with a picture of a good bios setup);

http://www.xbitlabs.com/articles/mainboards/display/albatron-km18gpro_4.html

They tested with a 1700+ processor which requires 1.50 V, 2700+ needs 1.65V. Did not mention Power supply, may not have enough to run the system with everything plugged in. 2 HD's ? DVD / DVDR/W / CD / CDRW / Floppy ?

by daz'n'ash

Tried all the BIOS flashes, none made any difference. Even Dr. Pro of Albatron support has no answers to this. Pity, Albatron used to be a good board, not anymore.

by daz'n'ash

OTL,
The power supply is new with the case. 400w PSU.
There is 1 CD Rom, 1 Liteon Combo, 1 80gb HDD and 1 FDD. Not a great deal of load on the PSU I would't think. I'll check the rest of the info anyway. Thanks.

by jailbreak_pt

Hi

If the board is new, maybe is better you go to the shop/company here you bought and they will teste and if is still has waranty, give you a new one.

That is what waranty if for

by daz'n'ash

Did that, they swapped it and the new one has a different problem that won't allow it to be clocked at more than 100 MhZ system bus speed.

by bwells47

Pull the lite-on combo strap untill you have every thing else configured. I had a lite-on burner one time that kept shutting down the system. Configured everything else first, then installed the burner, and everything went together well. I usually just start with the bare essentials-floppy,cd & hd. Get those going, then proceed. Computers do whatever they want, whenever they want to. It's worth a try.

by daz'n'ash

The problem was definately not hardware oriented. I did actually try this, but no change. Thanks for taking the time to reply, it is appreciated even if it didn't help me. I have discoverred that even though WE are the ones that make the computer work, they do seem to have their own mind at times.

by daz'n'ash

OTL,
The voltage is set just fine, the main problem seems to be the date/time configuration. Looks like all other settings can be changed. Never seen anything like it. Flashing the BIOs didn't even help. I have taken it back to the supplier for them to test and see for themselves. I will leave the question open. I really hate rejecting answers, so I think when I close this I will accept all answers anyway for the effort in attempting to help me resolve this issue.

by mikex

Here are some solution to your problems, but as it appear the best way to get thtough is to change the motherboard...

1. Question: the first board would set the date and time to Feb 2 2002, 2:2:2 and i couldnt change it. it would read my barton 2500+ as a 1100+ and would not save bios settings. i sent this back as recomened by the admin on here assuming it was just a bad board, however the replacement board is doing the exact same thing. all i wanted was a working board but nether have done so and i have spent around 30 dollars shipping them back plus now a restocking fee because of these bad boards. i have tried contacting Albatron USA by e-mail but they have not answered in the past week. please, i really felt this would be a good product and a good company, dont let me down. what should i do?

2. Answer: sorry to hear that...Please try and remove the bios battery for 20 minutes, then set the time in the CMOS setting-->load to windows, double check the time/date/region again.--> complete shutdown--> reboot system again and see the time/date will change.

If is still the same, you might wanna get dr.pro's help at dr.pro@albatron.com.tw for assistant. Did you shipped it to Taiwan?

This is from the Albatron Official site support

I hope it will save you some future troubles

by daz'n'ash

Tried this solution also, no effect. I give up, I will cut my losses and never buy Albatron product again.

This discussion is closed to new replies.