Discussion Locked

COM PORTS

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
Recentyly purchased palm pilot. Trying to synch this to my computer. Will not see any comports. I have 3 open comports showing in display manager and all not being used. I've uninstalled the comports and readded them. I'm running win98. Have nothing special running. Have norton antivirus, pc camera with usb connection. I'm really frustrated and this question means alot to me.

21 replies

by cdobbin

Well your problem is why all techs should carry loop back connectors, you should make sure that the setup on the palm pilot is the same as the config on your com port IE:7data bits, 1 stop bit, even/odd parity.
I do not have any experience with palm pilots but I am sure there must be some sort of configuration needed.

by steve.rocco

I have good experience with installing palms on computers. Config on this is what it should be.

by tommugg

I'm not really sure, but check your BIOS and make sure the COM/Serial Ports are enabled there. I have run into machine where these are off by default for some reason... not sure though.
Good luck to you.

by steve.rocco

This was exactly the problem. Seems so simple and I actually checked this and thought that I had made them enabled. However, after checking again, both were not enabled. Enabled in bios and worked like a charm. Thanks for the help.

by ddickerson

I had this problem with a palm also. It ended up being another program in the background hogging the com port. Just remember com1 it mouse and modem may be grabbing com2 so something may be grabbing the other com port.

Good luck

by jeeper

Check your Ribbon that connects to the motherboard. I have found that alot of ribbons go bad. It also my have just come unplugged. Hope this helps.

by wgirid

Hi!
I agree with most of what has been said, but if you have 3 com ports, none of them used, do you know for certain that they work OK? You may have an IRQ conflict that doesn't show until you try to use one of the ports. Try disabling/disconnecting "third" com port and use only built-in (?) com1 and com2 set at the normal addresses/IRQ. Verify that there's no competition for IRQ from some other device. If this doesn't help I think you may have to resort to testing com ports from DOS to see ifhardware is OK.
Regards
/RID

by steve.rocco

Comports are working and have no irq conflict. I had a modem on com1 which worked fine and I since have taken the modem out.

by mishratron

Reboot in Safe mode and make sure you do not have a ghost comports , Check for com port conflicts in your device manager if this does not work try going to another system taht has nothing on it and try it there.

by wlakey

If you have some kind of wheel style mouse, delete the driver out of device manager. also go into add/remove programs and remove any related software to the mouse. I have had Logitech mouse drivers that made windows unable to phisically access thecom ports in certain programs.

by landon021

I agree with answer # 5, if you have 1 and 3 or 2 and 4 both enabled at the same time you are going to have and IRQ conflict (they are trying to use the same resources), like as was said only enable ports 1 and 2.

Something else that I have seen work (a lot of our customers use a router that has to be configured via a serial cable), is going into the BIOS settings and change the port setting from AUTOMATIC to MANUAL, the actual port settings were still the same (COM1 -3f8/IRQ4) after rebooting they were able to get into the router, this might work in your situation also.

by landon021

I agree with answer # 5, if you have 1 and 3 or 2 and 4 both enabled at the same time you are going to have and IRQ conflict (they are trying to use the same resources), like as was said only enable ports 1 and 2.

Something else that I have seen work (a lot of our customers use a router that has to be configured via a serial cable), is going into the BIOS settings and change the port setting from AUTOMATIC to MANUAL, the actual port settings were still the same (COM1 -3f8/IRQ4) after rebooting they were able to get into the router, this might work in your situation also.

This discussion is closed to new replies.