13 replies
by ctos
The graphics card may be the problem, but I will try to reseat it first.
by dmiles
Check the grapuhics card drivers,boot computer into safe mode if you can and check for any exclamation marks in device manager
While in safe mode,adjust the refresh rate to the monitor,it may be to high ,this also apply to the resolution
by ctos
I will check the seat of the card, but am unable to boot to safe mode as it is a unit I just brought home without an OS. It was hooked up to the owners unit to place a mirrored OS on it to demonstrate it's functionality, but he removed the mirror before giving it to me.
I think you may be correct about the settings of the monitor being to high for the new unit, especially since there is no OS on it presently. Will try adjusting them and see what happens.
by jessie
by ctos
Poster rated this answer.
by willcomp
Jessie may be correct. It is common for cards to "pop up" in slots when a PC is transported.
Also check other cards besides video. Any loose card will cause boot failure. Ensure that contacts on RAM are clean (red pencil eraser works well) and that modules are seated.
Are you getting any beep codes? If so, post back with what they are.
Dalton
by willcomp
Video adapter should sync with monitor at BIOS level. Problems will not occur until Windows loads with high resolution or frequency or both set.
Since you don't even have Windows installed, that's not your problem.
by ctos
Actually this was a main issue, it would not get as far as Windows...thanks willcomp!
by hal 9000
Just make sure that you are using the right Video out socket as some of those Compaq units had a Dual Head Video card and in the POST setup if you are connected to the secondary video out it will remain blank.
The monitor should work provided it is the right type does the plug have 3 rows of pins? If it does it should be working at the very least on the POST. If you fitted anything before attempting to load the unit remove it but as Jessie said remove any add on cards and re seat them. If you have one of the Compaq's with a riser card on it to make the plug in cards lay on the same plane as the M'Board then pull that out as well and re-seat it to. If that fails then reduce the unit to a minimum installation the CPU, Heat-sink & Fan, the Video card if it isn't built into the M'Board and one stick of RAM and nothing else. When you get a picture on the monitor you can then start adding one unit at a time until it stops working and then you've found your problem. Just 3 days ago I had a floppy drive lead cause the exact same problem. No display on the monitor. It is a slow and tedious process once you get it working but it is really the fastest way to do things.
Of course if you do not get a display with just the CPU, Video and 1 Stick of RAM and the Video is built in to the M'Board ring up the person who you brought it from and make arrangements to return it for either your money back or an exchange unit. But if the Video Card is a plug in one try another slot if it is a PCI or try adding an old PCI card and remove the AGP card just to make sure that it isn't a bad Video Card. If the Video is on-board try a PCI {not the express type} on the M'Board and if you then get an image on the monitor go into the BIOS and make sure that the on board Video hasn't been disabled.
But first exhaust every possibility before making that phone call as you do not want to look foolish returning a working unit because you have overlooked something simple.
by hal 9000
I did that recently with a M'Board that just wouldn't power up when bolted into a case and when I returned it it worked perfectly but when back in the case no go, turned out to be a badly molded Reset button which was holding that switch in the ON position all the time.
Just as an after thought a new Battery wouldn't go astray either as that may be nearly flat and be causing your problems.
by ctos
Your comment about making sure the onboard video is not disabled was the key! I wish to thank all of your for your assitance and your suggestions. I will be keeping them around for any further issues with this unit! The monitor is working now, but it did not hurt to make sure of connections and cleanliness, etc!
by ctos
This discussion is closed to new replies.
Trending Desktop posts
Sort by Trending