Discussion Locked

Complete Shutdown Problem!

0 helpful
25 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Have a gateway E 3100 tower with Win 98 SE...
Win OS System was resently Re-installed!

Problem..Start/shutdown all ok../ computer shuts down fine ..Then in about 5 sec's restarts...
After I shutdown again ...hold power switch in to shut down...computer shuts down ..then restarts...
I unplug computer ...plug back in ...and computer restarts again with no outside help..

Ques: is this software or a switch problem ..if a switch where can one get a factory replacement...Gateway was nohelp at all!

25 replies

by shanghai sam

Tried MS download and no results! Also unloaded Win 98SE so I only have Win 98 ...still does it ...
Thanks anyway

by timthetoolman

Hi,

I dont believe this is a software problem...at least not one fixable by Microsoft - because if you completely power the system off and then power it on, it boots. Thats got nothing to do with the OS.

I'd say you have a dodgy BIOS setting. Many BIOS's these days have "Wake on" commands. Like Wake on network or Wake on modem.

I'd say you're being plagued by one of these settings. Check the BIOS settings and see what you can see!

If you need to verify that its not the actual switchcausing you problems...then unplug it off the motherboard. Apply power to the system and see if it still boots.

Cheers,
Tim.

by nigel100

hold down the del key on reboot to access the bios. write down the bios settings you have at present. then "reset to defaults" and save/exit.

in addition to the "wake on" commands in bios you should check the "str" jumper on the mainboard and in the m/b manual as it is in this area where you will find the solution (what type of shutdown do you want).

by gpierides

your problem is not software
its probably a hardware fault
maybe the ram is faulty
also may be a device is sharing an irq with some other and is causing this
try changing ram for start and then take it for repair

by jrbigsky

FOLLOW-UP I think we have something here from the tool-man below....
...I First got this computer second hand at a auction so where it came from no clue.. On start up I hit F1 to enter bios..
When entering Bios it has a password window.... I managed to get in past user password by just hitting enter... and got into bios..when I got to secuity tab there is a setting called "unattended start" and its enabled..but I cannot tab down to it to change it seems there is supervisor password which most likely has to be entered when I where I bypassed user password......if i had that I could change the settings... otherwise it will not let me toggle down to the setting to change it... ..so is there anyway to bypass this and get into it or is there a way find the password..i think this will fix problem?

by yule

Since the system automatically restarts, I don't believe it's the MS shutdown plague we all see alot of. If your getting the wake on lan/modem situation. Easy test may be to disconnect your terminal from the network/phone line.

The last time I had this happen, I did have a pushbutton switch that was actually stuck. I can't imagine why Gateway won't have a switch available. The one I replaced was about $5.00.

Beyond this. The Bios comments from the other submitters is the next area I wouldbe looking at.

by otl

@ things to try;

Get all settings for the system bios then remove the jumper for the bios (to zero it out, jumper is usually labled on the mother board.), or disconnect the battery for the bios.

If the above fails try flashing the bios with the latest update, should kill the password protection.

GOOD LUCK !

by johnfkk

I also have a gateway PC and found that it was a software problem. Microsoft has a patch available for a problem like this the file names are as follows.

4756us8.exe and 7507251.exe.
They are also available at the gateway web site.

by cnlson

my guess is.... switch
gw will not help you on warranty support line cause you didn't buy it from them. if you have a gw country store locally you could try having them either service it or order the part and charge you for it. otherwise they may have a "fee" or "out of warranty support" phone line to call to order the part.
easy way to check is to open the case.
find the connection that runs to the power button (with the power off) and disconnnect it
if when you plug the machine back in itturns on then you have a Ghost in the machine ;^) my guess is with the switch unplugged the machine doesn't turn on. good luck!

by cnlson

o and unattended start is a way to turn on the computer and have it get all the way into windows but still force the bios password to be entered if it says 'enabled' your kbd lights will flash when in windows until you enter the bios password

good luck

by harold.smit

To get into your bios without a password remove the battery from your motherboard remove the powercord, this will reset your bios, put the battery and the powercord back and turn on your PC
go into your bios and change it into default setting. If the PC still does'nt boot than you have a hardware problem

by volovoy

Create shortcut with the command line:
start rundll user.exe,exitwindows
and try to use it to shutdown your computer.

Good luck
Alex

This discussion is closed to new replies.