Question Locked

Computer turns on then off and then on again after RAM upgrade

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Alright here's the story. The computer I'm working on just needed an ram upgrade. Running Windows XP with 256 Mb of ram, upgraded it to 2gb of ram. I did the upgrade, closed everything up and went to turn on the computer. Nothing comes up on screen. When I power it up, it turns on for two seconds and then shuts down, only to turn itself back on a second later. I switched back to the old ram and I have the same problem.

I was grounded the whole time I was replacing the ram. The power cable was disconnected. I just put in another power supply to test it and it does the same thing. I'm a tad stumped here, hopefully someone can help me out?

17 replies

by formerly callpete.com

Sometimes, motherboards get confused after a hardware upgrade. The Plug-n-pray database in the bios can get unstable.
To do this, pull the power supply cord.
If there is an LED on the motherboard, press and hold the power button in, and it should turn off.
Locate the CMOS battery. It looks like a Quarter. There is a spring clip to remove it. Take a screwdriver and short the leads of the battery mount (the inside clip thing and the outside clip thing) and hold it for 20 seconds at least. Replace the battery, and more likely than not, it should come back to life.
If this doesn't work, even with the OLD memory, try polishing the memory contacts with a dollar bill, and trying it again.

Hope this helps.

by dbarboza641

I tried what you said but it still refuses to boot up. It's amazing that what should be a simple upgrade could turn out to be such a large annoying problem eh?

Edit: I've searched all over the internet at this point. I ended up finding some problems that were like mine. In fact some of them were posted here a few years ago. Sadly none of the results worked... If anyone has any more ideas at what could be wrong I'd be greatly appreciative.

by mg_roberts

sounds like the RAM was DOA. does it boot up when you use the old RAM? are you sure the motherboard supports 2GB of RAM?

by david.wallis

put the ram back into the correct slot to test?

can you post you rmotherboard make and model on here... and also the make and model of you ram?

thx

by david.wallis

did you make sure you have the smaller 4 pin power connector plugged in the board?

if still no joy, i would take the whole board out and refit it, you may find its earthing somewhere on the case

take it all out of the case and power it up on your desk see what happens (on an anti static mat ofcourse)

by dbarboza641

I tried putting the ram in both slots to see if it starts up but it doesn't in either case.

And yes the four pin connector is attached to the motherboard

I'm not sure the make of the motherboard. I tried looking it up on HP's website but I got no results.

The old ram is:
256 DDR 333mhz PC2700, some generic stick of ram that HP put in there I assume.

The new ram is:
1gb DDR 333mhz PC2700. It has a logo, not sure what the brand is since I don't have the order information.

by dbarboza641

It doesn't boot up with the old ram. I used the Crucial memory scan to find out the ram it can take.

by david.wallis

take it out of the case and build it on your desk see if it fires up......

you may have seated it incorrectly. there was a guy at my old place who put different size posts in for it to sit on so it was warped..surprisingly it didnt work :) but was ok out of the case

by dbarboza641

I rebuilt it outside of the case I ended up with the same result. It just refuses to boot up normally.

by david.wallis

have you tried one stick of ram at a time?

what CPU have you got in it?

by dbarboza641

I've tried one stick of ram at a time using one of each but it doesn't boot up.

I can't get to the Bios since nothing appears on screen and the keyboard doesn't respond to any commands.

I've disconnected and reconnected everything multiple times with different power supplies and the same thing keeps happening. It will turn on for a few second, then shut off for a moment, and then turn itself back on again staying on but with nothing on screen.

by sue t

made sure all of your connections are tight? Disconnect the hard drive and reconnect it, power and cable and also reconnect the ribbon cable where it connects to the motherboard. Do this for your CD/DVD drives and floppy drives as it is quite possible that something was knocked loose when you replaced the memory. Can you boot to a CD or does the computer still shutdown? Can you get into the bios?

by mg_roberts

well, i would say, take all the parts you had prior to the 'upgrade', take everything apart, leave it for about an hour, then build it back up the way it was from scratch. see if it boots, if not, chances are you killed something. if the new RAM was bad it could throw off the voltage regulation and fry the motherboard. unlikely, but possible. i've built PCs on shag carpet with no ESD protection, with cats walking on the parts and never had an issue with dead parts due to ESD. so i always have my doubts when someone suggests that it died from ESD. there always ends up being a technical reason why its not working.

by formerly callpete.com

Since it boots after a few seconds, it COULD be a bad (sticking or dirty connectors) on the power switch, or the reset button is building capacitance.
While you have it out on the desk our of the case, disconnect EVERYTHING except the power supply and the RAM (no drives, no ISA/PCI cards). Use a screwdriver to power it on (momentary touch the pins that the power switch normally connects to)

Also, unplug and inspect the keyboard and mouse pins. Leave them unplugged to test. I once took a PC from the customer's office to the shop, to the office to the shop and back to the office, before figuring out that it was a bent keyboard connector on the keyboard. (I couldn't reproduce the symptom outside of the office)

If the system will boot totally naked, try plugging things in one at a time. Keyboard [power on, boot, power off] mouse [power on,boot, power off] Drives, power switch connector, etc.

If the system WONT work totally naked (orig ram, no peripherals, no power switch, then you might still have a bad motherboard or power supply. If the power supply is putting out 10v where it should put out 12v, then things will work for a few seconds like you describe. You might try a known good power supply before tossing the motherboard.

by dumphrey

and reset the bios with a motherboard jumper. After resetting the jumper, unplug all power connectors, remove the cmos battery, give it an hour and then plug back up and see if you can get into the cmos. No cmos access is a motherboard or cpu issue usually. Did you clean the ram slots with compressed air? Fold a doller bill and "sand" the motherboard ram slot as well as the ram its self. Do you get any beep codes? Have you tried the ram in another computer?

by steeldocparker

don't unplug power cord . this is what grounds the computer , so the static has somewhere to go. do by all means TURN IT OFF . Maybe something got knocked loose? who knows somtimes its the simple stuff . good luck , i hope this hlps u some

This discussion is closed to new replies.