Discussion Locked

Floppies unrecognised by other machines

0 helpful
37 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have to run training courses and maintain the computers in a training room. They are stand alone systems running on XP and students are using Office 2003 and some training programs.

I have had (and continue to have) major problems with these PCs - they are self built (by a shop that went out of business), do not have Intel chips and they show Mercury on bootup. They seem identical but who really knows.....

The latest problem is the floppy drives - a disk formatted on one machine is not recognised by any of the others. I spend half my training time running around with a flash stick taking off small files. Buying new machines is not an option.

Does anyone know why this happens and what I can do?

Thanks

37 replies

by rmcneill

I had this occur many years ago. One of the floppy drives was out of alignment. When I formatted a diskette and copied data to it, another computer could not read the disk.

You should be able to run a disk test from the computer manufacture's diagnostic tools. If the disk drive fails the diags, replace the floppy drive.

by bewildered (most of the time)

Unfortunately the Manufacturer's diagnostic tools were not supplied - I suspect the machines are a cobbled together set of local builds (and in the Middle East the quality is very variable). The probelm (so far does not seem to be the drives but I'm sure at least one will have this problem - thanks.

by bewildered (most of the time)

Unfortunately the Manufacturer's diagnostic tools were not supplied - I suspect the machines are a cobbled together set of local builds (and in the Middle East the quality is very variable). The probelm (so far does not seem to be the drives but I'm sure at least one will have this problem - thanks.

by bewildered (most of the time)

Unfortunately the Manufacturer's diagnostic tools were not supplied - I suspect the machines are a cobbled together set of local builds (and in the Middle East the quality is very variable). The probelm (so far does not seem to be the drives but I'm sure at least one will have this problem - thanks.

by samthetrue

having used older computers i remember having this problem...
might want to make sure the disks arnt to new for the computers... if they are the computer might think it did it right but another computer might not be able to read the first computers work...
(or alterativly the disks arnt to old... i have seen people using 5 1/4 disks that they cut with sizors to make fit... you probably arnt doing that... but if you are it would solve your problem)

also might want to reinstall the drivers for the disk drives...

hmm if all else fails i suggest banging it in frustation... suprisingly that has worked...
(this one probably you shoudnt do...)

none of these are garanteed to work but i hope they do

sam

by bewildered (most of the time)

I was supplied with boxes of previously used disks and having bought new ones - these seem to have solved the problem with the few machines I have managed to work on. Most software is incompletely installed and many hardware devices are badly configured. Thanks.

by bewildered (most of the time)

I was supplied with boxes of previously used disks and having bought new ones - these seem to have solved the problem with the few machines I have managed to work on. Most software is incompletely installed and many hardware devices are badly configured. Thanks.

by bewildered (most of the time)

I was supplied with boxes of previously used disks and having bought new ones - these seem to have solved the problem with the few machines I have managed to work on. Most software is incompletely installed and many hardware devices are badly configured. Thanks.

by w2ktechman

I ran into this problem before, an alignment issue it probably is (as answer1). I fixed it by replacing the floppy drive.

by wlbowers

You can buy a floppy drive for $10.00, shipped to your door.

The alignment is off. They probably used questionable drives.
You can buy them bulk and test them your self. But Why?

Don't even try to align them. Put a new one in.

http://www.pricewatch.com

Lee

by rajuegypt

I bet the floppy media is SONY.

This incident occured in many offices.They had to buy another brand SKC or imation and it worked well without any problem.

so just buy one disk and try this same disk on all the computers. nothing else.

by nazil dsouza

hi mostly its either the floppy try changing the brand even i faced these prob then on changing them solved even check the allighnment of the drive and hey u get a image saying mercury well its the boot up screen u can disable in the bios thats in even sometimes intel shows up if u have an intel board

by bewildered (most of the time)

Very helpful answer - these machines are seriouslt weird - equivilent to less than Pentium 2's and firm-wired for Novell. They take very careful handling. The long term solution is a new job I think

by bewildered (most of the time)

Very helpful answer - these machines are seriouslt weird - equivilent to less than Pentium 2's and firm-wired for Novell. They take very careful handling. The long term solution is a new job I think

by bewildered (most of the time)

Very helpful answer - these machines are seriouslt weird - equivilent to less than Pentium 2's and firm-wired for Novell. They take very careful handling. The long term solution is a new job I think

by sue t

Probably your fastest and cheapest method at this point would be to connect these computers through a hub/switch or network and just download the files to each machine. Also, as the other person said, just for kicks check each computer to see if it is formatted as NTFS or FAT32. If that is the problem then either convert all to NTFS or make note of which computer is formatted as which and have to floppys, one done on each type and then use that floppy for that type of formatted computer. Good Luck.

by bewildered (most of the time)

Will check the FAT32/NTFS situation as I go along - no budget for anything at the moment - but changing the floppies seems to help so far. Thanks

Sorry about my response to your duplicate post - I thought it was a blank response.

by bewildered (most of the time)

Will check the FAT32/NTFS situation as I go along - no budget for anything at the moment - but changing the floppies seems to help so far. Thanks

Sorry about my response to your duplicate post - I thought it was a blank response.

by bewildered (most of the time)

Will check the FAT32/NTFS situation as I go along - no budget for anything at the moment - but changing the floppies seems to help so far. Thanks

Sorry about my response to your duplicate post - I thought it was a blank response.

by sue t

Probably your fastest and cheapest method at this point would be to connect these computers through a hub/switch or network and just download the files to each machine. Also, as the other person said, just for kicks check each computer to see if it is formatted as NTFS or FAT32. If that is the problem then either convert all to NTFS or make note of which computer is formatted as which and have to floppys, one done on each type and then use that floppy for that type of formatted computer. Good Luck.

This discussion is closed to new replies.