Discussion Locked

GeForce 2 MX Refresh Rate problems

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I posted here a couple of days ago with a problem with my GeForce 2. The problem has been whittled down to a refresh rate problem. Here is the problem in as much detail as possible. Again, I'm low on funds so I would like to try and fix it without replacing hardware if possibl3e.

System configuration
M/B: Azza PT-5VMD
CPU: AMD K6/2 450
RAM: 64MB 168 pin DIMMS
Sound: Sound Blaster Live! 1024
Graphics: Creative 3DB GeForce 2 MX
TV Card: Pinnacle PCTV Rave
Monitor: GreenView GM-6448 (about 5 years old)

Here is what the problem is:
When I start the PC I am unable to get a video signal. I don't get a signal until I'm into Windows, when I can only get it by turning the monitor off and on again. The same problems occur if I try to open a full DOS window or launch andything that goes outside of the Windows Desktop.

When I access either the Creative BlasterControl panel or Windows Display settings, and try to change the resolution to 640x480, the display will either be lost asit does during bootup (and I can't get the signal back by turning off and on the monitor) or it appears as a very short and wide image that is extremely bright.

I've tried different combinations of resoultion changes and refresh rates, and one ofthree things happen in each case:

1. The display will be lost and I have to switch back to the previous resolution and turn off and on the monitor.

2. The signal appears but the screen is very bright, short and wide.

3. The signal is lost at first but I get it back by turning off and on hte monitor.

I'm using the latest drivers for my GeForce 2 (Creative's 6.50 drivers) and when I shutdown the PC the same thing happens (I lose the signal). I can't access or flash the bios as it needs to be in pure DOS or startup, both of which denies me a signal.

I am grateful for any assistance people can offer me.
Thanks in advance
-Marc

9 replies

by freetech

i still feel that the source of your problem is your agp clock. i believe you need to set it to 1x. unfortunately, this can only be fixed in your BIOS. if you reset your cmos on the motherboard, that will probably reset you agp to a fail-safe setting (1x). just a thought, but proceed at you own risk.

by mapp84

Thanks anyway, but unfortunately it was the monitor which was the problem. Being 5 years old, it finally came to an end and died. I have now replaced the monitor and no longer have any problems. Thanks for your help.

by jwilczyn

I think, that your problem is your monitor.
Try to test your PC using a different monitor.
If you want to play with your old monitor - try to use refreshing rate between 60-70Hz. Old monitors don't suupport refreshing too high as 85Hz or higher.

by mapp84

Thanks anyway, but unfortunately it was the monitor which was the problem. Being 5 years old, it finally came to an end and died. I have now replaced the monitor and no longer have any problems. Thanks for your help.

by lwt

You may also want to get the correct .inf file for your make of monitor.

by mapp84

Thanks anyway, but unfortunately it was the monitor which was the problem. Being 5 years old, it finally came to an end and died. I have now replaced the monitor and no longer have any problems. Thanks for your help.

by wyldchilde

Make sure that you adjusted the refresh rate in both blaster control and windows properties. Otherwise, blaster control will try to override the windows setting and stick to optimal. You can also try these bios settings:
agp aperature 64 MB or half system ram
disable agp 4x or agp turbo

If you haven't installed the agp driver from you chipset manufacturer, you might install that. Certain non-Intel chipset manufacturers had problems with agp cards on some motherboards.

by mapp84

Thanks anyway, but unfortunately it was the monitor which was the problem. Being 5 years old, it finally came to an end and died. I have now replaced the monitor and no longer have any problems. Thanks for your help.

This discussion is closed to new replies.