Discussion Locked

Have SN and model how can I tell the MB

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I am trying to find out what kind of Mother board I have. No manufacturer is list on the board. The number is A161V12A and the S/N is A161A000107209. It is about 4-5 years old with an AMD 850Mhz processor, award modular bios.
Any info would help?

12 replies

by rg11

Someone told me it may be a shuttle? I need to find a manual so I know the max ram. I had a 128 mb chip and added a 256 and it is only seeing 128mb of the 256. If I put in only the 256 it is showing up as 128mb in bios and system.

by thechas

The easiest way to verify who made your motherboard is to use the BIOS code that is displayed at the bottom of the POST screen while the memory is being tested.

Then, use the tools at either:
www.motherboards.org or
www.wimsbios.com

to identify the manufacture.

You will still need to browse through the manufactures web site to identify your specific motherboard.

If this is a Slot A system, 128 MB per memory slot was a common RAM limit.
Even some early Socket A motherboards had a 128 MB per DIMM limit.

Another very real possibility is that your 256 MB DIMM is of a higher density than your BIOS and chip-set can read.
When quad density SDRAM DIMMs came onto the market several years ago, most of the older motherboards could not properly access the full capacity of the DIMM.
Make sure that the DIMM you have is a double density not a quad density.

Chas

by thechas

Looking at Stan's post, while it is possible that Shuttle made your motherboard, it could be an "OEM" board.

For most OEM motherboards, your only support option is the system manufacture.
As a general rule, part of the OEM agreement is that the motherboard manufacture provides no product support.

As a side note:
Did we help you?
If so, please rate the answers and close the question.

If we did not help you, please reject the answers and post a comment as to what further help you need.

Chas

by willcomp

While many Shuttle model numbers begin with an A, next comes a letter designating the chipset. I have never seen a Shuttle mobo with a number as the second character.

All that aside, I suspect you problem is installing high density RAM in a motherboard that does not support it. If your motherboard is a Slot A board, it most likely will not support high density memory.

You will need PC100 (or PC133) SDRAM with one or two memory chips for every 16MB RAM. A 128MB stick of RAM must have at least 8 chips and a 256MB stick must have at least 16 chips.

Support for high density RAM began with the VIA KT133 chipset for socket A CPUs. It was later coming for Intel socket 370 CPUs.

Low density memory is considerably more expensive. Your best source will be crucial.com. All their PC100/PC133 memory is low density.

Dalton

by willcomp

If Chas had been a little faster posting his reply, would have saved me some typing.

Most socket A motherboards were based on the VIA KX133 chipset and support at least 256MB per bank up to a maximum of 1024MB. Some support 512MB per bank with a maximum of 2GB RAM.

However, in all cases, they require low density (single or double density) rather than high density (quad density) RAM. Most SDRAM currently sold is high density.

by dmiles

Download and run CT BIOS. This utility may grab the manufacturer's info from the BIOS. In the case of my BIOS, it listed the manufacturer's web site URL among other things.

Visit Wim's Bios Page for help identifying the board with BIOS numbers.

Some boards just may have an FCC ID number on the board/slot, in the motherboard book, or elsewhere on the computer if the same manufacturer made more than just the motherboard. That number can usually be matched to the manufacture's name, etc. using the FCC data base at: http://www.fcc.gov/oet/fccid/. Use that info to find the manufacturer with an Internet search engine. This is also useful for finding the manufacturer of expansion boards, etc.

Other motherboards may just have the model number of the board on them. Run this number through some of the Internet search engines.

by laurent spielmann

Is it possible that you didn't read the ID properly?
no offense, just a question.

because a google search with "A161V12A" didn't show much (in english, that is)
but trying "AI61V12A" brought more results, and many leads that could make one think that it's a Shuttle MB:
http://forums.windrivers.com/showthread.php?t=13716&highlight=AI61V12A
for instance.

I checked Shuttle's website, support, dwnld manuals.
no more results for this request (too old I reckon) BUT a link to theit FTP server...
there I think I found what you're looking for:

open your favorite FTP client (ie6 maybe...) and go to :
ftp://ftp.shuttle.com/Manuals/en/ai61/
and DL the one you need....

by hal 9000

The most likely scenario is that you have brought some High Density RAM ind the M'Board isn't capable of reading it properly when this happens the machine only sees half of the available RAM. You really need to find the M'Board maker and you do that by either running CT BIOS or writing down the BIOS string on the bottom of the POST screen and then doing a search but you will also see the maker of the BIOS as well so that narrows down the search quite a bit as well. Since you didn't mention it you should have Award/AMI BIOS or maybe one of the other less used ones so you know at least where to start. If you can not access CT BIOS try these sites to find out who the maker is and then visit their Web Site and download a manual.

http://www.uktsupport.co.uk/reference/biosp.htm

http://www.wimsbios.com/

You will need to copy down the BIOS string correctly and you can pause the screen at this point so you can write it down along with the maker of the BIOS that you have while it is in the BIOS string it is faster not to have find that first when you already have it listed on the top of the same screen. Depending on the BIOS maker the various numbers should provide you with the maker and chip set type the model number that you supplied is incorrect possibly a typo so check that again as well just to be sure.

However if the problem is that the board will not recognize the new RAM you'll have to find some of the older stuff and use it because while you might get the unit working with only seeing half the available RAM there is no guarantee that it will be reliable and most likely will suffer constant RAM problems that result in the unit freezing or shutting down and restarting.

Col

This discussion is closed to new replies.