Discussion Locked

Help with modem disconnects.

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a Motorola SM56 56k modem and I cannot connect for more than 5 minuites. Could anyone please give me a link to a patch or help me. Please, I'm giving all of my points.

James

16 replies

by derekhyps

could be an interrupt conflict or really a port address conflict. if you can set your modems com irq and port address manually(disable plug and play) than in your bios setup change your selected irq to be legacy instead of plug and play. In windows since plug/play is turned off you will have to run the install hardware from control panel and manually config your modem.

by tuck46

usually line noise causing problem. Go into dialup networking and right click on your dial up icon and select properties. Click on configure,click on connection,click on advanced, uncheck error control and in the extra settings type "S9=30". That should stabilize it. You might also give your phone company a call and have them check for line noise.

by mphoffar

My experience with the motorola's has been that you need to limit the connection one notch lower then what is connected. The way I've seen it, Motorolas want to connected at a speed higher then actually the phone line can suppor, thus when it can'tachieve that speed, the modem tries to adjust and then disconnects.

If it's a v90 modem, you'll want to subtract 1333 and kflex subtract 2000. In other words if you're connecting at 48000, you want to limit your highest connection to be 46000 with kflex or 46666 with v90. Keep in mind also that v90 will not use a speed of say 47999, but 48000.

Make sure you know what you're running before doing this. You can usually get that from the diagnostics under modems or by doing an ati3 commandin a terminal.

To do this you would want to add an extra setting of +MS=12,0,9600, for a v90 modem or +MS=56,0,9600, for a kflex...where

by jesalyer

If this is a new Motorola, force MNP error correction:

ats48=128

If you still have problems, ats48=128+ms=v34.

Note that it is possible to get disconnected if your network protocols do not match the network you are connecting to. Whatever you do, remove Microsoft Family Logon and add Client for Microsoft Networks.

Good Luck!

jeff s
spanish support analyst

by qhcomputingny

Gypsyroo,
To help out your situations under Control Panel then modems go into the advanced settings and go to port settings. See how your port settings are set and if they are not on default, put them back to default,
but if they are on default and you are still having problems just lower the settings even more. If this doesn't work than this is not the solution. :)
Have a good day and hopefully you will figure this out.
Eddie

by gray ce works

I ALSO HAD THAT PROBLEM. WHAT DISPLAY DRIVER DO YOU HAVE? THE MOTOROLA SM56V.90 CONFLICTS WITH S3 DISPLAYS. MOVE THE MODEM TO COMM PORT 2-4 AND REDUCE DISPLAY ACCELERATION A NOTCH OR TWO. MAKE SURE MODEM SOFTWARE CORRECTLY INSTALLED. NOT JUST THE DRIVERS BUT ALSO THE SUPERVOICE SOFTWARE THAT COMES ON THE CD(SV\PICSHELL.EXE)TRY A DIFFERENT PHONE OUTLET/WIRE. USE A SURGE PROTECTOR.TURN OFF ERROR CONTROL.MAKE SURE YOUR DIAL UP IS CONFIGURED PROPERLY. WHO ARE YOU CONNECTING TO ANYWAY????I HAVE PROBLEMS CONNECTING TO SOME ISP'S BUT NOT OTHERS. HOPE THIS HELPS.

by foxmulder_65

Is this a internal modem? If it is, then you must remember that all internal modems are classified as software modems or winmodems meaning they generally rely on the CPU to function properly. If you are running intensive programs, you might be disconnect because your CPU is not delegating enough power to your modem. Another reason for an internal modem to not function properly is because of all the "noise" in the computer, thus interfering with the modem. So if your machine is not powerful enough, try using an external modem, it should work fine. If your modem is external then the reason would be that your telephone line is "noisy", line interference making it difficult to send data packets.

This discussion is closed to new replies.