Discussion Locked

Install 120 gbyte drive in Win 98SE PC

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I'm trying to install a Maxtor 120 gbyte drive in a pc running Win 98SE. Using Maxtor's partition/formatting software, I partitioned the drive into three 40 gbyte partitions and formatted them. I can then copy individual files into Drive C. But when I try to re-install Windows from a CDROM, there is no response. The installation program goes through the ScanDisk operation, sends the message that installation files are being copied and then the installation hangs, going back to the DOS screen with the directory letter of the CDROM blinking. The computer hasn't crashed. I can still copy files into the C drive. But I can't get Windows installed. I'd really appreciate some help on this. I currently have a 20 gbyte drive in the computer and it does not behave abnormally at all. I can re-partition it any way I like and have no difficulty re-installing Windows.

14 replies

by a. g.

I'd try making a directory called Win98 on the C: drive and copying the cab files from the Win98 folder on the CDROM. Then run Setup from the C: drive. It doesn't take up that much space on a 40 gig drive and that way the CAB files are there when you don't have the CD around.

AG

by korgmeister

if the cdrom installation didnt work after a few try, i suggest you have to install it from a hardisk. it should be working.

:)

by greysonj

The suggestions were appreciated and tried. When I called "setup" from the hard drive,first nothing happened. The cursor just kept blinking. Then fooling around, I got a general drive read failure message. I also tried copying the files to a logical drive ("D:"), and the same thing happened.

by dmiles

Check the motherboard manufacturer site for any bios updates

The cd rom may not be the first boot device in bios configuration
Boot computer at startup screen press the designated key to enter bios setup

In the boot device order select the cd rom as the first boot device

Reboot,using a windows start up disk(windows98) if available,select to run setup with cd rom support,it should then run installation,also you want to be sure that you have the first partition as the active partition

by hal 9000

Does the M'Board support a drive that big?

If it doesn't and there are no BIOS updates that do you can only use a drive that size as a Slave Drive as the Maxtor Utility tricks the BIOS into recognizing the drive but when you attempt to install Windows to it the setup utility ignores the Maxtor utility so the drive effectively no longer exists according to BIOS.

If you use it as a Slave with 98 loaded onto another drive it should work OK but I very much doubt that you'll ever be able to install 98 directly onto that HDD. Of course you could always Ghost a Copy into the Default Partition and then run the Maxtor Setup Utility from there to create the remaining partitions or use something like Partition Magic or System Commander to do the same thing.

Your problem isn't with 98 but the M'Board or the way you have setup the partitions with the Maxtor Utility. If the M'Board can actually read a 120 GIG drive use FDISK to create a 40 GIG partition and then install Windows to that and then using System Commander, Partition Magic or even FDISK you can create the rest of the partitions as you want them.

Col

by hal 9000

Of course you could always add a PCI IDE Controller Card and get around that problem of th Hardware not being new enough to support the drive. That would be a lot cheaper than replacing the M'Board. CPU, RAM.

Col

by willcomp

Do what Hal9000 suggested, but first low level format drive using Maxtor's utilities and start from scratch using fdisk instead.

Dalton

by bipin002

do dm of segate and again do fdisk when the place for disk size comes give % do not specifiy a number only give percentage other wise connect it to another machine and partition using partition magic and try again

by absolutely

I suspect that Maxtor's partitioning/formatting disk lacks the ability to make a FAT32 partition bootable, or that you forgot to do that. I would run Windows FDISK from a floppy, remove all your existing partitions and start over, being sure to make the first partition Active as well as Primary. As I remember, Windows FDISK will prompt you to make the first partition active, and will only make the first partition Primary, so you cannot go wrong.

My reading of the fine print that accompanied the Maxtor drive I bought recently suggests that there are very few situations in which they recommend that we use their software! My MaxBlast 3 CD says "Boot from this CD if you do not have Windows installed" but accompanying documentation makes (somewhat) clear that FDISK is really the way to go.

by absolutely

I haven't used Win98 recently, but doesn't it require that the system drive be the Primary Master? It looks like your 20G drive is still the Primary Master, and I vaguely recall that 98 can only be installed to whatever hard drive is installed in that location.

by absolutely

Give this a try: make sure you're using 80-conductor cables. Using 40-conductor ATA cables might cause your drive capacity to be identified incorrectly.

j/k, I saw your answer first, I did not think of the cable type as the source of the problem. It is interesting to know that it doesn't make communication impossible, just misreads the drive's capacity.

by jdclyde

Make the first partition 10 or 20 gig. I would go with the 10.

I would only load the OS on this partition then, loading all programs and data on the following partitions.

Older systems just don't like the big drives. You may end up running this as a slave with your 20 the master.

The other option is you may need to get a different disk controller to handle that big of a drive. The "promise" cards are not expensive, and work like a charm. If you want this to be the only drive, this will probably be the method you will need to go with.

by greysonj

I want to thank all those who tried to help. The error though was mine. I did not realize that the Ultra ATA cable that came with the drive was different from the IDE cable that had already been installed in the computer. The pin configuations are identical so I just plugged that old cable into the new drive. When I recognized my error (the ATA cable has 80 conductors in contrast to the 40 on the IDE cable) and used the proper cable, Windows installed just fine. My dumbness, but I sure wish the drive manufacturers would lay greater emphasis on the cable differences, especially in view of the pin configurations being identical. Thank you all again.

This discussion is closed to new replies.