Discussion Locked

Keyboard/mouse not working in Windows

0 helpful
24 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I am running Win2000 Pro and the other day, suddenly, my keyboard and mouse stopped
working. They work in the boot-up mode (tested because I tried to repair the Win installation) and also
work under a CD-run version of Linux. So I think it must be something with Windows.
The problem is I can't get either to work so I can't get in and change anything not even in VGA or safe mode.
Yes, I tried other keyboards and mice too. They are both PS/2 connected.

24 replies

by lhatcher

When you say that you tried other Keyboard and mouse, does that mean that they did or did not worked? I They did not, then the first thing I would try was a usb keyboard and mouse.

by e chill

The "other" keyboard and mouse had the same effect as the "original" keyboard and mouse. ie...I am not getting a keyborad error or no keyboard present on boot up, just when Windows loads. Since both sets of keyboard/mouse work within the bootup period and within Knoppix, I do not think it is hardware related at all. The question is, how do I fix this windows problem? I tried to "repair" my installation and do not want to have to format and re-install as that would be greatly heinous. I tried to re-install windows but I need to not have all my files erased when doing so.

by den inc.

you can actually re-install windows without deleting any of your files.

Setup windows, install as usual and choose to repair.

by e chill

I did try to "repair" and nothing works.
I would have already re-installed windows but when I do the
setup screen tells me that I will lose all data.
For expediency, (I need this machine to perform for a party in two days), It would be difficult and time consuming to transfer off all my files, then back on after re-installing "cleanly",

by sgt_shultz

i never heard of this one.
i would boot in Safe mode then go to device manager and remove the presumaably banged entries for the ps2 devices. then reboot so windows can refind the hardware and reload the drivers and see if reloading the drivers might fix it.
maybe consider hunting up latest mboard drivers and bios just as good practice...
maybe some device is conflicting. what have you added lately?

by e chill

Yeah, the old, what have you done lately? Nothing is the answer. I had a stable and together machine for a long time and nothing new either in hardware or softwares for a while now.
I just came home to an unresponsive keyboard and mouse.
Thus, I am not able to log in to be able to do any re-mucking up of the mouse/keyboard drivers. As far as bios and mboard, same problem, cannot get in to do anything.

by willcomp

I'm with Sarge on this one. Has all the earmaks of a driver issue. If so, keyboard and mouse will work when you boot into safe mode. Then you can remove and reinstall drivers.

Dalton

by e chill

I tried a USB mouse -- It works!! However, USB Keyboard does not.
Safe mode still wants me to log in so I am stuck.

by willcomp

How about a little help here. Are you saying that PS/2 keyboard and mouse do not work in safe mode?

In order for a USB keyboard to work prior to loading Windows, BIOS must be configured to recognize keyboard. USB keyboard support or legacy USB support or similar has to be enabled in BIOS. Use PS/2 keyboard for that.

Dalton

by willcomp

Reread question. Missed safe mode info first time around.

Apparently you can access BIOS with PS/2 keyboard. If so reset ESCD as suggested below.

Comment about USB settings in BIOS is still valid.

by e chill

Pointing in right direction but cannot find any functions in my bios (circa 2000) that relate to anything for the keyboard or USB for that matter at all. I do not know how to reset escd.

by sgt_shultz

what about using recovery console to restore registry to earlier version from repair folder. what about a rescue installation of win2k to edit the registry. what about a usb keyboard and mouse...
what about 'press spacebar for last known good config. do you have it at that point.
for a person that has linux on a bootable cd i am surprised you can't figure this one out...

by e chill

I have tried everything so far.
Having a Knoppix CD and being a Linux guy are far from the same thing.
Last good config rendered the same result. Repair of installation did nothing either. I am almost positive that what some of the others said as being Mangled drivers is correct. But I cannot get in and do anything about it.
I really appreciate your efforts. thanks.

by bvega

Had something like this. I went into BIOS and refreshed CMOS so that corrupt PCI interrupt table was recreated. Windows relies on this table more than Linux. Dells and Compaqs are notorious for these. Sometimes, just going into BIOS and changing a setting like SCSI or IDE field, WITHOUT REBOOTING YET, did it for me. Let me explain that when PCI table gets corrupted, interrupts are "Reassigned". SO your PCI video card no longer works because the interrupt that Windows has no longer matches what BIOS has. Hope this hits the nail.

Benny

by e chill

This machine is a "white box". AMI Mboard. This is definitely on the right track. I just started getting CMOS errors and so replaced the battery on the board. Until then I had 2 options: F1 to run setup and F2 to reset all settings and go. I did both to no avail. When I replaced the battery I stopped getting the CMOS error and had to reset the system clock to the correct time. But still no PS/2 keyboard/mouse will work. My USB mouse works but not my USB keyboard and I can't find any BIOS settings to change that.
Can you explain what you mean to refresh the CMOS and/or reset the PCI table?

by willcomp

Reset ESCD in BIOS (as previously mentioned). Usually found under PCI Plug and Play or similar. It is a yes/no or enabled/disabled choice and may refer to resetting Plug 'n Play or PCI. Set PCI to Auto, enable Plug 'n Play OS, and enable reset. Reset will run only on next boot, then will disable itself. If you need to reset PCI again, will have to enable reset again.

Add a comment to your question if you have any problems with PCI reset. 2 rejects on 1 question is enough. TR needs a better way to handle the back and forth required to find a solution.

Dalton

by bvega

Is there a Keyboard field in BIOS? Is it set to automatic? Can you change it to PS/2 and then try your PS/2 keyboard?

Benny

by wcp

This is most likely by a program that initiated KB and mouse services that started automatically when Windows starts.

The only logical way to disable the service(s) is from Repair Console.

Use LISTSVC command and see if there is any such service (There must be!!) and disable it by using DISABLE command.

This discussion is closed to new replies.