Discussion Locked

Mouse and cdrom problems winme

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

We have a SocketA M810 series with AMD 750 with 512MB machine running WinME on our router driven small office network. Out of the blue the PS2 mouse inexplicably stopped working completely. Several mice known to be good were tried - no difference.
I tried installing a genuine serial mouse - windows can't find it. Even after loading serial drivers - it thinks its a ps2
I tried a usb mouse - windows can't find it. No drivers load
I tried starting up from a floppy at this point and found that the winme CDrom couldn't be accessed (to make sure I had all the drivers needed). The drive was registered but it wouldn't read. After booting from the hard drive the CDrom is the same. It registers but won't read data. Without a mouse working its hard to diagnose the drive. Any ideas out there??

16 replies

by willcomp

First try this and post results in a comment.

Connect a PS/2 mouse and boot into safe mode. See if mouse works in safe mode. If so, you have a driver issue (safe mode uses generic mouse driver).

Also, if mouse works in safe mode, you can uninstall CD ROM and mouse drivers there.

Dalton

by willcomp

I'm still not sure of situation. Does PS/2 mouse work in safe mode? You mention drivers are installed but not whether mouse is working.

by bluerhino_0

PS2 Mouse does not work in safe mode even though the drivers load ok. The serial drivers do not load properky and will not update properly when using the manual update procedure

by bluerhino_0

PS2 Mouse does not work in safe mode even though the drivers load ok. The serial drivers do not load properky and will not update properly when using the manual update procedure

by bluerhino_0

PS2 Mouse does not work in safe mode even though the drivers load ok. The serial drivers do not load properky and will not update properly when using the manual update procedure

by bluerhino_0

Thanks for the response. I should have said - I have already tried every thing described in safe mode also and the results are the same. The ps2 mouse driver loads ok but the serial mouse driver (set up manually) has the yellow question mark - I have not found a way of resolving this. I am beginning to suspect the mother board

by dmiles

The symptins may suggest that you have a virus,check the system for any viruses.

The yellow exclamation denotes problem or drivers not loaded,open device manager,highlight and then click on properties,select to re-install or update the driver if this does not work you may try using the start up disk,insert in floppy and boot system,select to run setup without cd rom support,this process will reload the system and configuration files,once process is finished,eject floppy and reboot.

by bluerhino_0

The boot up with a floppy procedure did not help. The mouse drivers refuse to update properly.
I cannot run the antivirus for some reason (database is out of date probably). I only have the keyboard so running stuff is quite tricky. The pc will no longer communicate with the network

by bluerhino_0

The boot up with a floppy procedure did not help. The mouse drivers refuse to update properly.
I cannot run the antivirus for some reason (database is out of date probably). I only have the keyboard so running stuff is quite tricky. The pc will no longer communicate with the network

by liame

The symptoms could also be a shorting / knackered ps2 mouse port. Try disabling the port in the bios and see if a serial or usb mouse is detected after a reboot.

by bluerhino_0

I cannot find any option in the BIOS that refers to the ps2 ports. I do have options for the serial port though and it is enabled

by ozi eagle

Hi,
Try going into device manager and deleting both the serial and PS2 mice, then reboot. This forces windows to freshly reload the drivers.

by bluerhino_0

Hi Ozi
I deleted the drivers as suggested. On rebooting no mouse drivers appeared to load at all - the mouse option appears in device manager but no drivers listed. Any other ideas??

by ozi eagle

OK.
Go to add new hardware and follow the prompts until the search for new hardware finishes. After the search, assuming that ME didn't find your mouse, select No, Device not in list, then No, I want to select the hardware from a list, select mouse. Select Standard serial Mouse, finish and reboot.

This discussion is closed to new replies.