Discussion Locked

My PC can not boot in any mode in XP SP2

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
During boot attempt, after splash Windows screen, Windows XP SP2 stops without Logon screen - it does not show nor Welcome screen, neither screen with user account selection. Why ?

21 replies

by dryflies

It's either a hardware problem or a softwarew problem :-)
OK, try to stick the drive in known good and hopefully similar hardware. The closer the match the better. if it boots you have a hardware problem and not much can be done. The usual culprits are memory, glue chips or the processor. If however, you have the same problem in the known good hardware, stick the hard drive as a slave in another system and retrieve all of your critical data. Then re-install windows.

by jkaras

I take it that this happened right after you installed SP2? Did this pc already have SP2 installed previously and just recently it had this issue? If it is a new install just wipe hdd and reload XP without SP2. If it continues to hang then you can start replacing suspect parts like memory, hdd, then I would try the power supply. I doubt that it is vid card, possible vid drivers, but I think its SP2 not playing nice. I do know that you can use the win2k disk and select repair when you boot to it for 2k. I believe XP has that same function for XP. If you could provide more information like part types and recent software installs it would help isolate known issues that you are dealing with.

by zaphodtwin

I think the HW is OK, 'cause I've already installed second OS + SP2 to second HDD and I see the previous HDD & corresponding partition with all the data... But I have tried RC, copy data from System Volume Information folder - but without any positive result... :(

by adent888

Try running an XP repair from an XP cd. Boot from the cd, and choose install Windows XP at the first prompt, at the second prompt enter R for repair. The machine will reboot without your input. After the repair run windows update to update your machine. The repair will not overwrite any of your data.

by hal 9000

Well as you have not said otherwise I'm taking it that you have just installed SP2 and on the reboot the thing will not startup right?

Firstly as you are seeing the Windows XP screen it isn't a BIOS issue as if it was you wouldn't be getting past the POST screen. Now there are several options that come into play here if you have just installed SP2 and on the restart it wouldn't work then you didn't leave it long enough to properly load as on the first restart after SP2 is installed it has to go through quite a few processes to open Windows for the first time. If you rebooted the computer at a critical time you may well have corrupted the HDD's data and made it impossible to boot any more as the MBR have been damaged.

While the Repair option may work in more cases than not I've seen it fail so if you have your data backed up the easiest thing to do is to wipe the drive and reload from scratch and here I mean use a drive wiping utility to write 0's to every sector of the drive and when you boot from the Install CD you can format up the drive and do not use the quick format as while it should work it just might not where as the full format option which takes a lot longer always works perfectly.

Now if you have not backed up your data remove the drive and fit it to another computer with NT or 2000 at the very least and see if you can read your drive and recover the data. You could also just add another drive to your current computer and load XP onto that and then plug in the other drive on the other IDE channel and see if you can recover the data or repair the MBR's if it is unreadable.

There is another possibility though if the drive is now blank it is possible that at the very least one piece of hardware is not SP2 compatible if that has happened first try a different newer CD/DVD ROM drive and disconnect any burners that you may have if you only have a burner of some description try another newer drive and see if it will work.

by hal 9000

As you didn't list the hardware I do not know if you have enough processing power or memory to run XP + SP2 so if none of the above are of any assistance please post back with your hardware configuration and we'll see what we can come up with.

Col

by zaphodtwin

My HW configuration is: P4-1600Northwood/640MB PC2100/2700 / 20GB (where problem is) + 120GB (where I've installed second OS + SP2 - it works yet :) ) /R9600SE / etc.

You see, I've installed XP + SP2 in Sept.2004 and it works quite good till 10, May, 2005...
One item that I suspect can be last spoil on system life: O&O Boot defrag that can not complete its operation in that evening...
I already use RC, tried copy data from System Volume Information folder - but w/o any positive results...

by karma1

Hey...

Okay, hopefully your motherboard isn't like mine or this will be a pain in the.. ahem. Press F8 to get to the Windows Boot options. Choose Safe Mode. The screen will now fill up with the files Windows is loading. Watch the list and write down the file it stops on. This file is usually the one with the problem.
Seeing as you apparently have access to another computer, either post the filename as a comment to your question here, or goto Microsoft's Kowledgebase. Choose Advanced Search, select your operating system, and put the filename in the keyword search. Then sift through the results and see if you can find a KB article that let's you know what's happening.

You could also boot off the XP CD and do a repair install. Hell, just reinstall XP if you're bored.

by hal 9000

OK now we know that you have had the unit running and it has only recently fallen over after a long time of running with SP 2 installed. The previous answer was based on the belief that you had just installed SP2 as you had not said differently.

If you have another computer available or another hard drive I would suggest removing your corrupted HDD from your computer and trying to read it on another one to see if it is still readable. To do this you will need a computer running NT4 or better. Alternatively you could pull your existing HDD and load XP onto a different HDD even if it is only a 10 GIG drive and then once XP is installed turn it off plug in your original drive as either a "Slave" or on the other IDE channel and boot up again. You may have to go into the BIOS to set the drive parameters for this depending on your M'Board. When the system boots up see if you can read your original HDD. If you can backup all of your data and then you can proceed to try to recover from the problem that you are having.

If you are unable to read the drive the MBR's have been damaged and unless you have access to some very good recovery software it will be cheaper just to wipe it and reload. If you have some "Must Recover" data on the drive and you have not backed it up then it is a job for the Data Recovery companies as they will have the software and hardware to recover your data. But be warned it isn't cheap!

by hal 9000

If you are unconcerned or have a data backup all you need do is wipe the drive and reload "Yes I Know It's a Pain" but it is really the only way out. If you can read the drive then after backing up your data you can power down and reinstall the original HDD and then place the XP Install CD into the CD/DVD ROM Drive and boot up from the CD. proceed normally until you reach the screen where you are given the option to install/repair or exit chose repair and then follow the prompts you never know it might work but I wouldn't be holding my breath waiting. From previous experience I've found it faster and easier to just wipe and reload the drive as I have not had much success with the Repair option but none the less it is worth a try.

Lets know how you get on.

Col

by edihardjono

I had a similar problem several months ago with Win2K. So I reinstalled win2k on a different folder. Then when I reboot, I have the option to boot the old Win2K. It worked. Then I just changed the boot.ini and delete the new directory.

This discussion is closed to new replies.