Discussion Locked

no video after i built new pc

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
i can not figure out why i cannot get any video now that i have built my pc

8 replies

by thechas

Lots of possible causes, including bad parts.

Things to check:

Make sure that the CMOS jumper is not set to clear.

If the CMOS jumper is in the run/normal position, try clearing the CMOS. Many times, you need to clear the CMOS so that it can properly detect your CPU and RAM.

Verify that all power connections are fully seated.

Make sure your video card supports the default (lowest) AGP speed of the motherboard.

Make sure the video card is fully seated in it's slot. AGP cards use an interleaved connector. The card need only be a few 0.001" from being seated to cause problems.

Double check that the CPU and RAM are a match for the correct Front Side Bus speed. And, that the CPU is supported on your motherboard.

Remove any other plug-in cards and see if you can now boot up.

Make sure the voltage selector switch on the power supply is set correctly.

Also, make sure that the mounting standoffs are not shorting the motherboard to the case.

A brief list, but a good start.

Chas

by willcomp

What Chas didn't say outright but implied is that there are a number of things that must function to have a display (video).

In addition to Chas' excellent suggestions, disconnect signal and power cables from all drives and remove any add-in cards (except video adapter) prior to troubleshooting. It helps to reduce system to fewest components required for a basic boot.

Also helpful to know the following:

Any fans running when powered on?

Any beeps? If so, how many and pattern?

Power LED on motherboard lit? Usually a green or yellow LED surface mounted on motherboard that lights when power cord is plugged into power supply (and PSU switch on if one is installed on back of PSU).

Dalton

by melvin_780702

Another good practice would be checking if your power supply's output is within the range of the rated output...but you need a multimeter for that....PC parts wont function properly given underrated supply...

For troubleshooting, you need to replace the basic parts one by one to eliminate every other possibility of the cause....problem is do you have the resources (known good parts)

Good luck

by courtpctech

I can agree with replacing parts to an extent, but a simlper method is to reduce the machine down to it's basics. I'd remove everything except one memory module, the CPU (of course), and video card (if it's not integrated). By doing this, I mean to unplug the hard drive and CD interface cables and the floppy interface cables, and removing any add-on cards that aren't needed to make it boot. It could be either a bad card or a bad (or misconnected) drive.

Try to power up after that and see what you get. All things being equal, the machine should at least get to a POST screen.

You very likely may need to reset the CMOS before it comes that far in the boot process. I've seen that happen numerous times on brand new machines, so it's a fairly common thing. It even happens occasionally when upgrading the BIOS. The motherboard's manual will give you specific directions on how to reset the CMOS, especially if it's possible with jumpers or switches.

Good luck!

by douglasb

Make sure your power supply is set to 115v, not 250v. Sometimes that switch gets bumped.

by v_odd

i have had something similar where i had been messing about in the case and unintentionally unplugged one of the USB cables (being the 4 single wires) for the front USB ports on the front of the case

by j.lawton

I had the same problem.
I would recommend as a first step removing the graphics card and testing it in another machine. If the card is OK that is one potential eliminated.
If the card does not work then you need to replace this before going any further but you may want at this stage to test the PC with a card that is known to be good so that you know this is the only problem.
My recommendation is that having established the card is working you then strip right back taking the motherboard out of the case and simply connect the power supply to the board (usually 2 connectors these days) and to the card. One stick of RAM (make sure it is in the correct channel) and hopefully a connection to the speaker. I achieved this by laying the m/b on top of its anti static bag inside the PC case so all the connections reached OK. At this point I finally got display and beeps which meant that my problem was a short. (Caused by some padding that was glued to the inside of the IO plate making it difficult to locate the m/b properly. I simply removed this and reassembled). Just to make sure I then replaced one screw at a time checking that everything worked after fitting each screw and then the same as I connected each component. I am glad I did this as I did find a non functioning stick of RAM. This sounds like a lot of effort but in all it probably took me an hour and had I done this in the first place instead of messing about for half a day I would have been less frustrated!

by eugene86

Ordered stuff from NEWEGG, built it. when I turn it on all fans work, but no video output!!

This discussion is closed to new replies.