Discussion Locked

Operating system not found (XP)

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have an IBM Intellistation M Pro model 6868sb3
that I wanted to replace the hard drive with one
that I have in an HP Pavillion XT993 since it is larger. When I install the drive from the HP into
the Intellistation, I get the message Operating system cannot be found. If I hook the HP drive up
as a slave I can read the information on it, but I cannot get it to work as the master drive in the Intellistation. I have tried resetting the jumpers on the HP drive which is a Samsung SpinPoint V60 Series SV0602H. Any help or ideas
are much appreciated.

14 replies

by jessie

Check the bios, make sure the hd is detecting with the correct number of heads and cylinders. You may have to set it manually, if possible. Also, you can try booting to an OS floppy, and sys the drive. "sys c:"

by dmiles

Check that your motherboard supports the large hard drive,the bios may need to be updated.

The problem may exist because the XP operating system may be setecting different hardware during the boot process,the system will not verify the system settings of the new board.

by willcomp

I'm not sure of everything that's in play here, but one thing is certain. You cannot swap XP drives from one PC to another unless they are identical or nearly so. As a minimum must be same chipset motherboard.

So it's almost certain that drive from an HP PC will not boot into XP on an IBM PC.

Is Samsung drive recognized by BIOS and correct model number returned? XP should try to start and then abort when it sees hardware changes.

BIOS setting should be Auto for primary master.

Some things to try:

Change IDE cables. Set jumper to CS and try that setting. Ensure boot sequence in BIOS is correct.

Dalton

by psjjl

hmmm..go to the bios setting, set your hard drive manually, make sure it is not in 'Auto' mode, switch it to 'LBA' mode. This always happen in big drive.

Hope this will help.

by hal 9000

The info on CHS Cylinders Heads Sectors is on the sticker on top of the drive. All you have to do is actually look at the drive and read the data.

Col

by hal 9000

Anyway you will still need to go into the BIOS and change the HDD around so it can be recognized but even then it is unlikely to actually load as all the required drivers will not be present. Just because the 2 systems may look the same doesn't mean by any stretch of the imagination that they are the same as even the little things like M'Board Drivers will most likely be different. The only cure is once the HDD can be recognized by BIOS is to wipe it and then reload the complete computer from scratch with the Recovery CD's that came with the computer that you are attempting to place the replacement HDD into.

by edihardjono

Check the boot.ini, then check if the operating system is on the correct partition recognized by the bios.

Once I installed a HDD from a dell computer to a no brand name computer. THe boot.ini shows the boot partition is on partition(1) instead of (0). I found out later that there is a tiny partition on the HD that is used by Dell exclusively and my other computer doesnot recognize it. SO it did not boot up. After I changed the boot.ini entry, it worked.

Hope it helps.

by borginva

Someone may have already said this above but I do not have my glasses on really.
My cousin once thought the same thing and I proved him wrong. That new drive, I will call it, was loaded with XP on a PC with certain hardware. Putting it into another PC with different motherboard, bios, video, etc, the OS was not loaded up to handle this new hardware. It was loaded with certain drivers and such for the hardware in the PC this hard drive was in.
I do not believe you will be able to get this drive working without reloading XP for the new hardware settings, especially for BIOS and the MB.
Good luck.

by carlos0463

This is big NO since Win2k. Different HAL = no go on win2k/xp. Only way to do it would be to clone the old drive to the new one.

by ozwes0071

IBM has a diagnostic partition on some systems, you may find that the bios doesn't recognise this partition. If you use a tool like Partition magig 6.0 etc you can check each drive to see if they both have this partion. If they do you can Ghost the original to the new one, careful they are usually hidden. The diagnostic partition is usually where the MBR is kept. You could also just try deleting this partition, and resizing the XP one to suite, don't forget to mark it Active and Primary. A small note also, XP will not run without running a sysprep on it though as it will not allow more than a specific number of hardware changes.

by chorito

The question is..... Is the OS cannot be found being given by the BIOS or the boot.ini ....

Is the BIOS seeing the Hard drive..?
You can run FDISK to see all the partitions and verify that the BIOS is picking them up...

Hope this leads you in the right direction...

by chorito

The question is..... Is the OS cannot be found being given by the BIOS or the boot.ini ....

Is the BIOS seeing the Hard drive..?
You can run FDISK to see all the partitions and verify that the BIOS is picking them up...

Hope this leads you in the right direction...

by wlbowers

You cannot change drive between computers with xp. It will not reallocate the drivers for the ide drive controllers.

The easiest way is to do an inplace upgrade.

MicroSoft Knowledge Base

Q315341
http://tinyurl.com/2zgk

Lee

This discussion is closed to new replies.