Discussion Locked

Overheating when surfing

0 helpful
4 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

One of my workstations with a pentium 3 processor alerts me to processor overheating when opening websites with lots of graphics. The heat ranges from 70C - 90C. On closing the site, heat range immediately returns to normal. Just noticed that it also occurs when an installation is performed.
Any feedback would be greatly appreciated.
Thanx

4 replies

by jamesrl

What is your fan situation?

If you just have a heatsink and not a fan on your CPU, I would recommend getting one. You need thermal paste as well. Google for installing CPU fan and I am sure you will find instructions.

I presume you are using onboard graphics as opposed to a video card? My vid cards have fans, but cheaper ones don't.

You might also look at a case fan. Most cases have an opening for a fan to vent the case itself. This can make a big difference, especially if you have a lot of cards/HDs/CDRW etc. For about $10 it can make a big difference and its easy to install.

Is the heating causing any instability in the system? If you were sustained at 90C I can see things getting unstable.

James

by synchronize

i agree with james .. overheating should cause instability to your system .. the heat range from 70-90'C u say? .. CPU fan are important nowadays .. :)

what kind of temp monitoring software are u using? maybe the setting is wrong? .. i notice you said the overheat occur when opening a website and installation are performed .. if u use 1, u should look into the setting ..

how are your HDD working? .. i think HDD could be 1 of the cause to the overheat issue .. most probably the HDD are not functioning well and data transfer (ie cache, temp files) could result overheat .. altho this can only be confirm if CPU fan not installed or the casing airflow are not "flowing" ..

:)

by hal 9000

The other thing to look at is a build up of dust and other crud in the Heat sink under the CPU Fan.

Being a P3 this is now getting a bit old so more than likely it's also dirty inside the case as well particularly if the box sits close to the floor and carpet.

I would first pull off the side cover make sure that the CPU fan is working at the very least and clean it out at the same time. I've seen instances of dust buildup in the heat sinks that prevent the fan from running correctly and they run slow and even worse don't allow the Heat sink to do its job of keeping the CPU cool. Since this has been working previously that would be the first thing to look at and then also check the air flow openings to make sure that they are not blocked.

Generally speaking you need air flowing in the front of the case and out the back the side vents if any only detract from good airflow over the parts that actually need the air to flow and take away the heat. I tend to block these off with masking tape on the inside of the case particularly any holes behind the M'Board as they only allow air to escape where it's not actually passing over anything and really any air flow in/out of these vents is wasted.

If the heat sink and Fan are all clean replace the Heat Sink Fan unit with something newer or if you have a passive heat sink [one without a fan] remove it and replace it with an active one with a fan attached and plug it into the socket that should be on the M'Board. You should then have software available to monitor the fan speeds to see if its actually working at the right speeds.

by hal 9000

If you have some ducting that is supposed to force air onto the heat sink remove it and fit an active Heat sink fan assembly particularly if it's one of those 80 mm fans sucking unfiltered air from the back or side as they cover the M'Board in dust and much that you really do not want. I would go as far as removing the ducting and reversing the fan so it is blowing out of the case and if possible fit a case fan in the front to suck air in but it all depends on where the computer actually is if it's close to carpet you'll want to keep the air flow down so not as much dust and other much is sucked into the case.

When I place computers into very dusty conditions like Site Work where there is earthmoving going on I am now using the Zalman Fan less cases and they work very well. Previously we used to work on the idea of one computer lasting for the life of the job and then dieing but with the fan less cases they are now running on and not breaking. As these are only fairly new they probably are not for you but one that I've built has lasted for 6 jobs so far and still going strong so the outlay for the case seems to have well and truly paid for itself several times over.

Col

This discussion is closed to new replies.