Discussion Locked

PC unable to power on

0 helpful
20 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

After emigrating to the UK from Australia, my PC had accumulated a lot of dust. Today I decided to remove all of the components from the machine and get rid of the dust. After I had done this I put all of the components back in place and ensured that they were seated firmly. I connected the power and video cables then pressed the power button. The CPU fan moved slightly but nothing else happened. No lights, no sound, nothing at all. Power is going to the motherboard because slightly inserting the ATX power cables into the motherboard results in a barely audible clicking noise. I have connected everything as it was before and as is stated in the motherboard manual, and I have never had a problem like this before.

My basic specs are as follows:

Azza PT-5VMD Motherboard
AMD K6-II 450
64 MB RAM
Webstar Spectra 3000 GeForce
Sound Blaster PCI64

Thanks in advance to anybody who is able to help.

20 replies

by burtsa

If it is an AT motherboard not an ATX I would check the powersupply cable that go to the montherboard. They probably are reversed.

Shawn

by mapp84

Sorry, I didn't clarify myself on that point. The motherboard accepts both AT and ATX connections, but my power supply is ATX. Thanks anyway.

by dmiles

Check the back of the power supply for a voltage switch and see if it is set for 110/220 and set it appropiately for the correct setting could be International Voltage Setting that could be causing this problem

by mapp84

The voltage setting is the same for the UK as it is in Australia. All I have done to the computer is taken the parts out, cleaned them and then put them back in. I haven't changed anything at all. Thanks for your help anyway!

by marcask

Since you did not mention weather you tested the PC after shipping it from AU to UK, I am going to assume you didn't. What I would like you to do is to remove all the i/o cards from the system board along with the floppy and IDE i/o cables. remove the keyboaard, mouse, and if the pc is so equipped, the usb devices. There should be nothing attached to the system board (if your pc has a riser card, leave it in. Some PC's will not turn on without it). If the p/s turns on, the problem is in one of the peripheral devices. Just attach them one at a time for the culprit. If nogo, remove the 2 pronged switch lead from the sys. bd and install a jumper or somehow carefully short the leads. If nogo, remove the memory. If still nogo, remove the ATX p/s lead from the system board, locate pin 14 (grey or green wire 4th one from the edge surrounded by 3 black leads) and short it to one of the afore mentioned neighboring grounds. When you apply power, the p/s should spin up (keep hard drive power lead connected)No= a bad P/S, Yes= a bad system board. I have always equated shipping to manhandeling and cringe whenever I have to put my PC in a box.

by otl

Don't remember if AU is 50 or 60 hz but UK is 50 hz. The system will not power up if the frequency is off by that much. A transformer to change the frequency or a 50 hz power supply may solve the problem, there may even be a jumper in the power supply to change the input frequency required.

by mapp84

I haven't had any problems using it in the UK until now, and that's without changing any power settings at all. I have used it for over a month with the Australian settings still in place. Thanks anyway!

by richard_barsby

Answer No 5 is incorect as with all modern psu's the AC voltage is converted in to a DC supply immedeiatly at the input by a bridge rectifier and capacitors. I test pc psu's with a DC limeted power i/p so as to try to limit damage when first poweredup after repair therefore the frequency of the mains has know bearing on the subject. If you have not used the PC before cleaning then I guess that the soft switch psu is not running. This could have failed in the uk and you would not know this if your psu had power to it all the time ie not switched off at the wall,if this is the case then the start up resister for the soft switch psu has gone o/c this is quite common.

Best Regards

R.K.Barsby

by bv2

I don't know for sure, but I would guess that you shorted something when you were removing cards and your power suppy is kaput - just because it is supplying power doesn't mean it is supplying enough - try replacing the power supply...

by mapp84

Yep, replacing the power supply worked. Now I have another, bigger problem. See "PC unable to power on - phase 2: The Motherboard and The GeForce"

Thanks very much!

by pc_emt

Mate the best I can give you now is verify that the power cables coming from the p/s to your mother board aren't on reversed. Use the motherboard manual to check this. Also test the voltages of each of the lines coming out of the p/s to the motherboard. These new motherboards love and need a stable voltage.

by kms

Several things could cause such a problem. I've had the ATX Power Supply connector on the motherboard have a bad connection. I'd reseat it first. Then you want to check the lead from the power switch to your motherboard. Make sure it is on the right pins and that it is seated good. I'd disconnect all drives (both power and data) and fire up the system and see if it comes on. If it does, you probably have a data cable on backwards. Removing all cards except video is a good thing to try. Good luck!

This discussion is closed to new replies.