pc will not boot up on good hd
i know the hd is good because it worked on another pc
will allow you to install win 95 then when you reboot
will say invalid sys disk
both pcs have same board, mem, cards
board is 486 dx2, amd
Desktop
i know the hd is good because it worked on another pc
will allow you to install win 95 then when you reboot
will say invalid sys disk
both pcs have same board, mem, cards
board is 486 dx2, amd
by moflic
Most likely you have a bad memory chip. Switch SIMMs from the working computer just to make sure, or boot from a diskette with device=himem.sys /testmem:on in config.sys. Try also changing the memory access times in CMOS setup>chipset setup.
Could be also a boot sector virus, or the virus protection activated, but in general win95 displays a warning that you should disable virus protection from CMOS setup.
Also do a
fdisk /mbr
to rebuild the MBR. Perhaps windows cannot write it properly.
by patrick_wood
by dmiles
by patrick_wood
by shadow
1- Check Your Bios settings and make sure that the disk is recognized and is selected as the 1st bootable drive.
2- Run Scandisk to make sure you do not have any bad sectors that are hanging out on your boot partition. If it finds bad sectors letit mark them as bad.
GOOD LUCK!!
by patrick_wood
by chrusher9
by patrick_wood
by csheltcomp
by patrick_wood
by shawkengin
by patrick_wood
by bdgray
Just copy the system files to the HD using a good WIN95 boot disk.
i.e.
SYS C:
Did you use Ghost? Sometimes you have to SYS a drive after ghosting it.
by patrick_wood
by lee v.
by patrick_wood
Hi!
If your BIOS supprts the HD then follow theese steps and 95 will boot up.
If BIOS dosen't support your disk get some disk management software as suggested in previous answer.
1. boot with DOS disk and remove all partitions.
2. REBOOT
3. boot with DOS disk and make a primary partition that is 1024Mb if this dosen't work try 512Mb instead.
4. REBOOT
5. boot with DOS disk and format partition.
6. Install Win95 and when done Win95 will be up and running.
7. Now go to dos prompt from Win95 and create any additionla partitions you want.
/Hasse
by patrick_wood
by riyaz
If I were u;
I will make sure the hard disk jumper is master.
cd-rom is secondary. (better for performance)
if it's connected with a Atapi cd-rom make hd jumper master & slave present
I will detect the harddisk from BIOS.
Save & exit
Boot from Diskmanager. offcourse virus free & protected. also with win95 system. not ontrack bootloader.
run DM /x
/x option is to avoid diskmanager detecting the Hard Disk Brand because I do not know the Harddisk model also it's little hard to get exact diskmanager for the harddisk.
use manual installation & create partion.
this will format & transfer the 95 system to c: drive
install cd-rom if u have.
if u are using diskette version please check for virus with mcafee 4.0 or latest. make sure CD version is OEM or Orginal Copy from Microsoft, other wise check viruses for cd also. (it's on the internet mcafee.com)
Install & configure your plug & play cards configurations with the utility comes with P&P cards, ex: Creative SB
insta
by patrick_wood
by frank.duffey
This Problem has nothing to do with your hardware.
This is a software related issue:
1.) check Format of your HDD (Fat 32 or fat 16.
2.) Did you FDISK the drive and remove the current partition?
3.)Did you make the partition active?
4.)Did you check the drive for a Virus using a Win 95 Boot disk and a Virus Scan Such as PCScan from PcCillian in a dos mode.
And Finally try using this command with FDISK:
A:\FDISK/MBR
4.)FDsik should be on your Win 95 Setup Disk.
Hope this helps ypu out.
FD Networking
Frank E Duffey
by patrick_wood
by tysonmathews
NO NO NO NO
go into you CMOS AKA BIOS and change your Boot up order.
It may either not be set to boot C or you have the 3 1/2" boot floppy still in and it is set to boot A,C or A,CD ROM,C and there is a CD in.
on boot up hit delete or what everit states to enter setup. THAT IS THE DEAL!
by patrick_wood
by tysonmathews
Do not format do not change your ram do what my last post stated. everything is fine. it is your boot up order or you have a 3 1/2" floppy in or a CD Rom in still and it is set to boot those. WIN95 CD ROM is not bootable
Just follow my last post to you.
by patrick_wood
by eswoodland
by patrick_wood
by vmm
by patrick_wood
by patrick_wood
This discussion is closed to new replies.
Sort by Trending