Discussion Locked

Power but nothing on the monitor and monitor shows amber light instead of green light like normal.

0 helpful
20 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have a Gateway desktop PC that when powered on, won't display anything on the monitor and the monitor shows amber light instead of green light...I have switched video cards and power supplys, but still the light on the monitor is amber but it works perfectly connected to another PC...Can anyone tell me what might be wrong??? I think maybe the processor or the motherboard might be blown or messed up and need to be replaced??? just need to know how to test the motherboard and CPU to see if it's one of them...

20 replies

by mjd420nova

If you've already swapped the video card and power supply, the other cause is the mother-
board. If the power supply is okay, the Hard
drive should be heard spinning up. The first
thing should be the video booting, showing a
video bios, then a beep and the CPU bios loads
on the screen, counts memory and checks the
keyboard by flashing the lights. If it doesn't
beep at all, it's possibly a memory card that needs to be reseated or replaced.
reseating--replacing

by 3xp3rt

There are some reasons for no video signal.
1. Bad video card, or video card moved and no connection to motherboard. Try to press firmly the video card into motherboard.
2. The motherboard don?t let the boot procedure to begin. The reason may be malfunction of cooling fan, or power problem. The power is on but maybe the VA not enough for normal function of the computer.
3. Malfunction of some other piece like memory, other PCI card and so on.

by mathisona

I would try to reseat the memory first. Just take the memory card out and push it back in. If that does not do it, try a different PCI slot for your video card.

by brenda4444

I had beeping and no monitor/no power up. Reseated memory card and THAT'S ALL IT WAS!! Thanks!!

by nz_justice

Might be that your hard drve and CDrom are both set to masters cahnge your cd rom to a slave. IF your using or have IDE connections this is important unless yuo use to diffrent IDE cables for both devises, not to sure about SATA it depends on your mother board, if your PC is still under warrenty take it to the store.

by colonel k

I had exactly the same problem after I upgraded the HDD on a Gateway PC. The PC failed to boot when powered up. I did all the usual and checked the board, power supply, video card and RAM. The PC still failed to boot when I put the original HDD back in. After about 3 days I was ready to dump the PC. Finally I fixed it - the PC failed to boot because it was connected to a KVM. Unplugged the KVM and connected a keyboard, mouse and monitor and the PC booted up fine, even with the new HDD.
I am still not sure why, and I have never had happen on any other PC before or after.

by nash984954

Sounds like you're locked in Standby mode. Change your power settings after you procure another monitor to test.

by nogeekhere

Can we assume you have tried changing the monitor's cable? Or you have tried a different monitor with this computer or this monitor on a differnet computer? If not, that would be the first place to start.

by stepmonster

If you have a digital + analog monitor, there is a button with square with an arrow going through it on your monitor. That button implies "switch me from digital to analog" or visaversa. With the computer powered up, Press it once and wait.

by it24

Definately sounds like the video is bad. It is quite possible that the other video card is bad also. You might try another slot. Other things to try would be to unplug ALL devices except the motherboard and video card you should get a series of beeps if the video is bad. You may just have a bad slot.

by lastchip

It may be your motherboard BIOS has become corrupted. I had a machine this week with exactly those symptoms and clearing the BIOS fixed it.

In order to reset the BIOS, take a look at the motherboard (or manual) and see where the jumper is for resetting the BIOS. Disconnect the mains cable and reposition the jumper to clear the BIOS and reset it default values. Having left the jumper in position for thirty seconds or so, replace the jumper back to it's original position, refit the mains cable and see if the machine boots up. If it does, you will probably get a checksum error, so enter the BIOS set-up pages, set the correct date and time and see if you need to set the CPU settings (some BIOS's require it, others don't).

If you can't find the information regarding the jumper, disconnecting the mains cable and removing the motherboard battery for a similar period, will achieve the same objective. Just be careful not to break the retaining clip. Reassemble as above.

While you're inside the case, just make sure all cards, memory and suchlike are firmly in position and it's always a good opportunity to clean out any accumulated dust.

by bluron

You have already been given many excellent suggestions, now here is one that will probably sound silly but try turning the plug from the monitor to the video card around. this happened once to my son, who had connected the monitor but had the cables connector upside down. this will be the cheapest and easiest effort at correcting your problem. good luck

by jsloan1223

Does the PC beep when you turn it on? If not, then it's not completing POST and you are probably bumming. If it beeps, pay close attention to the beeping pattern (write it down).
This link from gateway http://support.gateway.com/s/Servers/COMPO/Cases/3501746/4000943/3501746faq22.shtml (scroll way down to the bottom) has a list of the various beep codes and what they mean.

If it doesn't beep at all, you either have a bad power supply and/or motherboard and/or processor. PS sometimes when processors break, they take the motherboard with them..

by darkreign

I had the exact problem. Upon starting my Gateway computer, it would boot up; however, the monitor would not receive any signal. If I immediately shut the computer off using the power button and restarted it again, the monitor would turn on at the first or second try. Occasionally, I would see a "your hardware has changed screen prompting various boot options". When I restarted the computer via the shutdown screen, the computer and monitor would restart normally. If the computer was left off for a few hours, the monitor problem would reappear. I changed the bios settings, reinstalled Windows XP, installed various versions of the ATI video driver, changed power management settings, turned off background & startup items, and reseated the video card & memory. Nothing worked. I removed the video card (ATI Radeon 9600 Pro) and used the integrated graphics. Everything worked fine. Put the card back in and then, the monitor would not come on upon starting the computer; however, it now came on at the welcome screen. It seemed to not receive a signal until then. The fan on the video card spun normally as were the other fans. There were no signs of damage upon visual inspection. I have another Gateway 500 with a Radeon 9600 so I swapped video cards. The Radeon 9600 worked fine in the problem computer and the other computer now had the identical monitor problems with the Radeon 9600 Pro installed. I would like your opinion as to whether I may have overlooked something. Are the problems I described typical of a defective video card? The power supply is a Lite On 160 watt supply. It may be related. However, I kept the Radeon 9600 in the first computer and it has been booting and starting normally along with the monitor. The Radeon 9600 Pro has been shelved. I also switched memory between the computers with no problem. PS. I'm perplexed as to why the video card operated normally once the monitor/system was running if defective.

by darkreign

Forgot to mention that I have the latest bios and chipset drivers installed as well. I also adjusted display options like refresh rates and other ati control panel settings.

by jsloan1223

The best way to test if the problem is the motherboard and/or processor is to switch then out with compatible components that are known to be functional. So unless you have a duplicate machine, you are going to have a hard time trouble-shooting this issue.

by bluron

a while back you had problems with your monitor and i am curious if you have found a solution to that problem. would appreciate your advising what worked best for you. many thanks ron

by bryanlockyer33

Hello my friend, i'm having the same problem, i have no signal to my monitor, (which works on other pc's), i'm running a ASrock, dual channel-dual core pentium p4 3.06ghz, onboard graphics, (soz only just got pc), 760mb ram(sd), single dvd-rw, Maxtor 60gb H.D.D, wehn powering up pc, no beeps, hard drive light shows active, pc boots to windows but no signal to monitor, any thoughts??, oh the pc crashed just before this problem started, did a restart then no monitor!

by patrick.e.specht

Same problem. No fans spin up, no HDD running, absolutley nothing. PSU is brand new, but the entire unit is over ten years old. No boot, no monitor signal. Perhaps a bad motherboard? Please advise.

This discussion is closed to new replies.