Discussion Locked

Router problem

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello,
I just replaced a cisco 1700 router with a Sonicwall TZ170 router. The problem that I am having is the Sonicwall router will not recognize the Wlan cable when it is attached. I don't know why. When the Cisco router is attached it the cable works fine, but when I unplug it and attach the Sonicwall the cable seems to not work. I don't know what is wrong, this is on a Frame Relay internet connection. Please any help would be great, Thank you

Dan

21 replies

by ghimpe--

The cable doesn't work?? or are you talking about connection? Did you configured the router?? You can't expect to just plug wires and everything will work as "you" desire. Routers aren't exactly "plug and play".

If you didn't configured the router, configure it, if you already did post back and maybe we can still help you.

GooD LucK! ;)

by redcell593

Yes I did configure the router, the problem that I am having is that the connection is down, The router does not see that a cable is pluged into the wlan port, I have replaced this cable with another patch cable but that did not work..

by black panther

Try

Hard Reset ( Power Cycle on the router )

Re-boot the PC before attaching the Sonicwall - attach it then do a soft reset.

Try the router on 'another PC'.

Update the firmware to the router.

Does it have a USB connection you can try.

Have you tried support from the Distributor

by zaferus

Let's check some basics to start:

Some WAN connectors will "autosense" if they are xover or patch and will correct automatically if it is wrong. The Sonic's don't autocorrect. So get a certified patch and xover and try them both. Then take the xover from a switch on the LAN and plug it into your WAN to see if you get a connectivity light. If you don't your Sonic's WAN port is fried. Reply back if one of these combination of cables DID work. I've got a few Sonicwall certs so maybe I can help you here.

Zaf

by maxwell edison

You may need it install "SonicOS Enhanced", which is an optional software upgrade that builds upon SonicOS Standard to deliver advanced features for more complex network installations.

This is especially true if you have the SonicWall TZ170 SP or TZ170 wireless.

by ddevans888

Dan,
The problem is clearly in the router. Either the Port has a problem or there is some sort of configuration problem. Have you checked that there is not a duplicate IP address involved. Hook the Sonicwall to a laptop off of the network and compare all the settings with your Cisco

by jdclyde

Is the line a static IP address or DCHP?
Are you using a straight through cable instead of a cross over cable?

Call your service provider to make sure that the line is up.

SonicWall support is EXCELLENT at helping to troubleshoot their products. It should have come with free support for at least 90 days even if you didn't purchase additional support (which you will want)
[b]
WAIT A MINUTE! What are you using for a CSU/DSU? Do you have an adtran box or something? The Cisco may have had this built into it, while the SonicWall will not! Call SonicWall on this.

by artk

The TZ170 is NOT a router, it is a firewall. Put your Cisco back up and run the Eth0/0 that used to go to your LAN to the WAN port on the TZ170. You will need to know some IP addresses to get it all working, but it will.

by mmc3110

hello,
hope u r fine..First of all you have to check your connection of cable and if you have configured your router ...sometime some connection from cisco router to any other router may not work properly if cable is not connected properly...so you can check this...you also have to check the cable distance and finally you have to check the configuration ....

by shmaltz

Just my $.02
Is the cable cross over or straight? just swap the cable of the oposite.

by jt

what type of wic was this wan cable plugged into? If the port
block is lablled anything other than WIC1-ENET it's not an
ethernet drop, judging from your frame relay comment your
dealing with a T1 that is plugged into a dsu card (WIC-T1-DSU).

if this is the case, the firewall will never work directly and you
will need the router in between. If the frame relay is an
integrated product (split voice and data) and is handed off in
standard ethernet (from an adtran iad, or some other such
equipment) you will need a crossover cable, orange and green
pairs should be flopped on each side.

by kryptos

What is the WAN interface on 1700 Router ?

TZ170 has ethernet Port for WAN connectivity

thx,

by powerion3

I agree with your previous responder the router problem will be easier to respond to if you identify the "cable" you are having the problem with: what does it connect to? is it one that is inplace or did it come with the new router. Also you must have a working configuration with the correct informationon the port for a router to work properly. Get back to us on these issues.

Corky

by dacook

Did you try the simple first. Maybe you need to replace the X-Over cable with a straight.

Just might work.

by estebandelatorre

You will need to ENABLE the Wlan Interface first in order to make it work.
Then configure clock external or internal?
Who puts the clock into the wlan interface, the FR-Modem or the router interface?
Hope it help!

by dpekol1

The Sonicwall TZ170 is a firewall with several other features. It is not a router. You need to have the cisco router-CSU/DSU plugged into the frame network with the internal interface plugged into the Sonicwall (using a crossover) The plug the internal sonicwall interface into the LAN switch. Configure the external IP of the cisco router with the ISP info and the Internal Cisco with the first available public IP that you have been provided. use the 2nd available public on the outside sonicwall interface and NAT the remainder for you LAN devices as needed.

This discussion is closed to new replies.