Discussion Locked

SATA drive not recognised

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi

I have another question about my SATA drive!

I have just had to reinstall my OS (WinXP Pro SP2), on a Dell Optiplex 270. I have three drives in the computer - 2 IDE's and one SATA. The system partition is contained on the Primary Master which is one of the IDE drives.

I reinstalled because the computer would not boot. I continually received a BSOD IRQL_NOT_LESS_OR_EQUAL. I think it was caused by my ATI Radeon graphics card, but installing the latest driver and removing the driver and the card from the system made no difference.

The SATA drive contains a lot of data - about 50GB of music/movies.

When I initially ran setup after booting from the XP CD, setup refused to recognise my C: drive as a valid partition. As it did not contain any data, I told Setup to delete the partition and create a new one. However, Setup next claimed that the partition was not compatible with XP and that XP could not be installed on it.

In order to get XP to install I had to remove both the second IDE drive and the SATA drive. After I did this, Setup recognised my IDE and repartioned and reformatted.

My problem is that after reconnecting my SATA drive, the system cannot read it. It gives a message saying the drive is not formatted and "would I like to format it now?"

Just in case you are wondering, I did not remove the partition on the SATA drive during Setup - Setup lists the drives by drive letter and volume name.

Does anyone know how I may get WinXP Pro to read the data on my SATA drive? I will be very pleased with any help.

Thanks

8 replies

by willcomp

I'm suspecting that you may have, in fact, deleted partition on SATA drive during setup.

Setup probably designated the SATA drive as Drive C. Previous logical drive designations will not carry over and setup will reorder drives depending on how they are connected. SATA drives usually take priority and are assumed to be the boot drive on systems with Intel SATA controllers (no F6 drivers required unless RAID is used).

Dalton

by willcomp

For Intel ICH5 and ICH6 SATA controllers, it is not necessary to install drivers (F6 install) when installing XP without a RAID array. The same is true for nVidia 250 and 350 chipset SATA controllers (Athlon 64 motherboards).

Since it's a Dell, it's an Intel chipset motherboard and probably has either ICH5 or ICH6 southbridge.

by blackcurrant

Well, Damn! I think you are probably right! The size difference between my SATA and primary IDE drive is minimal. I likely did not realise I had deleted the partition on my SATA drive. After the experiences I had with Norton Go-Back assuming the SATA drive was a bootable drive, and your answer then, I am obliged to accept your answer now.

You did it again. 10/10

by black panther

Maybe some help here?

Loading Windows XP on a SATA drive
Just in case anyone else has this problem and doesn't want to spend an hour figuring it out...

If you are loading Windows XP onto a computer with a serial ATA (SATA) hard drive, you will have to manually load the SATA drivers.

As suggested on this usenet post, you need to put the drivers on a floppy disk.

Copy the drivers from motherboard support CD *\DriverDisk\SATA\*.* into root directory of floppy disk. (i.e. root directory of floppy disk should contain \pide and \sata folders, txtsetup.oem, etc. files.)

Then, boot system by Windows XP installation CD, when the message "Press F6 if you need to install a third party SCSI or RAID driver" shows up, press "F6". Then, press "S" to specify additional device when next screen pops up. Put the driver floppy disk you made in and press enter to continue. If the floppy disk is made successfully, the installation program will ask for selecting driver. Please then select "VIA Serial ATA RAID Controller(Windows XP)".) After SATA driver loaded and Windows XP can recognize the SATA HDD, you can continue to install Windows XP as usual.

This should work fine if you have the drivers on a CD somewhere

``````````````````

You need to copy the SATA drivers from the MBoard CD onto a floppy disk. When first starting the WinXP install, a screen will appear that says to hit F6 if you need to install any SCSI or 3rd party drivers. Hit F6 and supply the floppy disk. DO NOT remove the floppy disk until instructed to.

Here's what not to do:
1) Pull floppy drive from another computer
2) Get lazy and not install the floppy, simply hang it by cables on the side of computer
3) After using floppy, allow the exposed circuitboard to touch the case
4) Watch smoke come from the floppy drive since the power was shorted out
5) Toss floppy drive in the trash

by blackcurrant

Hi, subtropicalmist. Thanks for taking the time to answer. I know your response is correct to a certain extent, but I was trying to install WinXP on an IDE drive, not a SATA drive.

Your answer may be applicable if I was trying to install on the SATA drive, but the SATA had already been formatted as NTFS and I was expecting to be able to re-connect the SATA drive and access the data on it.

Well, at the end of the day, I am the twit!

by hal 9000

Well Subtropicalmist is correct you should have installed the SATA Drivers when you installed Windows but since you didn't and you most likely do not want to rebuilt the system again you could try the adding new hardware wizard and then try installing the SATA Drives from there treat it as if you have just added it on an already loaded computer. The problem here though is that depending on the M'Board make and model it just might set the SATA drive as the primary drive and make Windows unbootable as the Master Partition is no longer where Windows expects to find it. I don't know if it will work but if it does your ahead and if it doesn't all you need do is power down remove the SATA drive plugs and power up again and it should run.

Just as a side note whenever I reload a computer unless it is one of those off the shelf types I wipe the HDD with a Disk wiping utility which writes 0's to every sector that way Windows Setup can always recognize the drive and install the partition/s that you want as it sees it as a new drive.

Col

by blackcurrant

Hey! HAL 9000! Thanks for answering. I liked the idea of using the Hardware Wizard to identify the SATA drive. Unfortunately, because the drive was not formatted, the wizard did not recognise it.

Unfortuntely, I think Willcomp is correct

By the way - I have admired your Avatar for quite a while - wher does it come from?

This discussion is closed to new replies.