Discussion Locked

ScanDisk scans only 60% ?

0 helpful
19 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

My drive #d only will scan to 60%, and will
not defrag, my c,e drives are ok just #d
what can I do to fix this.

hatman98.

19 replies

by bwklatt

Huh? Which is it? Are you running SCANDISK (Error Checking Status) Standard or Thorough .. or.. are you running DEFRAGMENTATION ?
Do you get a message something like "Scandisk has restarted 10 times..."? If so, press Ctrl-Alt-Del to bring up the Close Program Window and End Task on all programs except for Explorer. If that doesn't help, restart in Safe Mode (press F8 at bootup) and Scandisk will complete OK.

by mike o

It's also a good idea to disable the screen saver and make sure the power settings in the advanced screen saver properties are set to never.

by jmstitt

try booting to a command prompt

Press F8 at the "starting windows XX" display during boot up

at the safe mode menu, choose boot to a command prompt

at the command prompt, change to the C:\windows\command directory

then type scandisk.

This method will allow you to run scandisk without any interference from windows. If it doesn't complete, you have a problem with that partition. Could need reformatting or may be permanently damaged.

After completion just restart the computer.

by mm212

How long have you left it at 60%? If it hangs for a few minutes, I'd say you have a bad sector on the hard drive. When it hangs, listen carefully to the hard drive. Do you hear what would best be described as a "clunking"? Every hard drive sounds a little different, but what it's attempting to do is repair the bad sector(s). I would first attempt a DOS-based scandisk with surface scan and leave it overnight. I'd be it will have continued by morning and probably will have found several bad sectors.

If it's still at 60% in the morning, I'd move all my data off of my D: drive, then reformat it (full, not quick). Once this is complete, try a DOS-based scandisk with surface scan again before moving my data back on.

by csmith

If you have left it overnight as suggested by answer #4 and scandisk has just frozen, the next thing to check is the partition table.
If the partition table is good, tape backup the drive, it may be about to fail.
I have two Seagate drives in my junk box that did this before they quit totally.
If they are Seagate drives, Seagate has an excellent utility on their website that you can use after removing the data from the drive.
Regards, Chris

by pdpjp

I have had this problem before with two customers and on those occasions the controllers were bad on both.
Remove the drive from the system and try place it as a slave on another system. Run scandisk and if it completes, then it is the controllers (at that point you should replace the motherboard). If the scandisk doesn't run on the other system, then you have a bad drive.

by william jay

IS there something keeping files open on the d: drive? (ie: running webserver logs), scandisk will be very patient to wait for the file to close, and defrag will appear syrupy slow to complete the checking file structure .....

by contra-heald

well there are two things that keep scandisk from completeing its job, #1 is Screen Savers.
#2 is Active Tsr's in the system tray.
SOLUTION is Click on The START MENU, then select RUN,then type in MSCONFIG and push ENTER. you will be at a window called system configuration utility,there will be 7 tab buttons on the top, Click the one that says START UP,next you will see a list of componennts that have CHECKS next to them, UNCHECK EVERY SINGLE ONE!then click APPLY, then OK and reboot as instructed and Thenn try your ScanDisk Utility, BETCHA it wont stop at 60% this time.

by hatman98

thank's for tring to help, but my system crash, lost everything, and took out the pations now I can scandisk.

thanks hatman98.

by hatman98

I would like to thank everyone who tried
to help me slove my problem, but my system
crashed, and i lost everything wiped out, so again thanks.
hatman98.

This discussion is closed to new replies.