shutdown issue
I have winXP (prof. sp2)installed on my computer.
when i click 'shutdown' option from start menu, it takes long time to show me the 'standby|shutdown|restart' dialog box.
Can nebody help me out.
thanks
avijit
Desktop
I have winXP (prof. sp2)installed on my computer.
when i click 'shutdown' option from start menu, it takes long time to show me the 'standby|shutdown|restart' dialog box.
Can nebody help me out.
thanks
avijit
by avijit_hp Accepted solution
by sgt_shultz Accepted solution
in my humble experience this is usually due to a bad driver or outdated software, sound cards and anti-virus are two examples.
you really need to find out or it will be much guessing. I would check the system and software event logs on the problem pc to see if you can figure out which software or device is causing this.
Alternatively, I would consider following the steps in this mskb article to enable verbose logging to help pinpoint the problem. (Unless you can remember some software and/or driver you might have installed just prior to this problem cropping up. If so you may want to go straight to that website and look for an update to apply.)
from support.microsoft.com
How to enable verbose startup, shutdown, logon, and logoff status Messages in the Windows Server 2003 & XP family
Article ID : 325376
Last Review : June 21, 2007
Revision : 10.0
This article was previously published under Q325376
For a Microsoft Windows 2000 version of this article, see 316243 (http://support.microsoft.com/kb/316243/).
How to enable verbose startup, shutdown, logon, and logoff status messages
To enable verbose status messages by using Group Policy Object Editor
In a domain environment
On a stand-alone computer or a single computer
To enable verbose status messages by using Registry Editor
MORE INFORMATION
SUMMARY
This article describes how to configure Windows so that you receive verbose startup, shutdown, logon, and logoff status messages. Verbose status messages may be helpful when you are troubleshooting slow startup, shutdown, logon, or logoff behavior.
Back to the top
How to enable verbose startup, shutdown, logon, and logoff status messages
You can enable verbose status messages by using Group Policy Object Editor or by editing the Windows registry.
To enable verbose status messages by using Group Policy Object Editor
To enable verbose status messages by using Group Policy Object Editor, use the method that is appropriate to your situation:
In a domain environment
If you are in a domain environment and you want to enable verbose status messages on a group of computers, follow these steps: 1. Click Start, point to Administrative Tools, and then click Active Directory Users and Computers.
2. Right-click the container for the domain or the organizational unit to which you want to apply the policy settings, and then click Properties.
3. Click the Group Policy tab.
4. Click New, and then type a descriptive name for the new Group Policy object (GPO).
5. Click the new GPO that you created, and then click Edit.
6. Expand Computer Configuration, expand Administrative Templates, and then click System.
7. In the right pane, double-click Verbose vs normal status messages.
8. Click Enabled, and then click OK.
9. Close Group Policy Object Editor, click OK, and then quit Active Directory Users and Computers.
Note Windows ignores this setting if the Remove Boot / Shutdown / Logon / Logoff status messages setting is turned on.
On a stand-alone computer or a single computer
If you are using a stand-alone computer or if you want to enable verbose status messages on only one computer, follow these steps: 1. Click Start, and then click Run.
2. In the Open box, type gpedit.msc, and then click OK.
3. Expand Computer Configuration, expand Administrative Templates, and then click System.
4. In the right pane, double-click Verbose vs normal status messages.
5. Click Enabled, and then click OK.
6. Close Group Policy Object Editor, and then click OK.
Note Windows ignores this setting if the Remove Boot / Shutdown / Logon / Logoff status messages setting is turned on.
To enable verbose status messages by using Registry Editor
Warning Serious problems might occur if you modify the registry incorrectly by using Registry Editor or by using another method. These problems might require that you reinstall the operating system. Microsoft cannot guarantee that these problems can be solved. Modify the registry at your own risk.
To use enable verbose status messages by editing the registry, follow these steps: 1. Click Start, and then click Run.
2. In the Open box, type regedit, and then click OK.
3. Locate and then click the following registry key:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Policies\System
4. On the Edit menu, point to New, and then click DWORD Value.
5. Type verbosestatus, and then press ENTER.
6. Double-click the new key that you created, type 1 in the Value data box, and then click OK.
7. Quit Registry Editor.
Note Windows does not display status messages if the following key is present and the value is set to 1:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Policies\System\DisableStatusMessages
Back to the top
MORE INFORMATION
If verbose logging is not enabled, you will still receive normal status messages such as "Applying your personal settings..." or "Applying computer settings..." when you start up, shut down, log on, or log off the computer. However, if verbose logging is enabled, you will receive additional information, such as "RPCSS is starting" or "Waiting for machine group policies to finish...."
by mdphoenix Accepted solution
Try some basic stuff. Like cleaning up the drive and defragging. Running an adware scanner.
CleanUp! @ www.stevengould.org is a good start.
Then AdAware @ www.lavasoft.de.
They're good utilities to have anyway.
by jjrichards.dps Accepted solution
dont try to do to much to early, download all of these programs and install and run them one by one, doesnt matter which order you do it in, after using the last one you shouldnt have anymore probs, if you do and it annoys you that much you should do a repair install as this works very well with xp pro here are the progams,
http://www.download.com/3000-8022_4-10401314.html
http://www.ccleaner.com/ ( run this one several times)
http://free.grisoft.com/doc/20/lng/us/tpl/v5
http://free.grisoft.com/doc/5390/lng/us/tpl/v5#avg-anti-virus-free
http://www.speedguide.net/downloads.php
finally if you using norton anti virus 2003 then i recommend you get another its nothing but trouble :) use avg anti-virus its free as are all the programs above.....if your problem persists then download hyjackthis( see here for download instructions)
http://www.techspot.com/vb/topic19133.html
and do a scan then post the completed scan report here>
This discussion is closed to new replies.
Sort by Trending