Discussion Locked

Trying to connect serial mouse to a IBM

0 helpful
24 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have this problem with a IBM PC 300 GL-62877BS:

When I connect a serial mouse to this computer, it doesn't detect it.

I have tried everything that came to my mind, changing bios setup, installing manually the driver of serial mouse, changingcom1 configuration, even updating the bios, but none of this desperate changes worked. It most be some way to make these mouses work in the ibm pc, and it is very important to me to figure it out, because I have a lot of serial mouses in stock, and a lot of IBM computers with the same problem than this one. Perhaps is something I don't know about IBM computers.

24 replies

by tlccomputers

There is nothing special as far as I know about IBM computers with serial mouse. I know this may sound too simple, but have you tried more than one serial mouse with this computer? Could possibly be a defective mouse. Other than that, you might check device manager (if you know how to navigate your desktop using your keyboard) to see if it shows any problems with your serial port. You could actually have a bad serial port.

by raquelmc

As I said, I have a lot of serial mice, all of them new, and a lot of IBM computers. I have tried different combinations. Thank you.

by paulp

Have you tried installing it on Com2? I know it sounds irrational, but I seem to recall hearing long ago that a serial mouse will only work on Com2. I may be crazy, but it couldn't hurt to try.

by dmiles

Turn the computer off and then connect the serial mouse to connector,boot up computer and see if the mouse is detected
One other thing to try is use the keyboard to navigate to device manager and delete the mouse that is listed,if one is listed.
you can ref.microsoft kb article Q82545

by raquelmc

That is the normal procedure. It was naturally the first thing I tried. Didn?t work and thats why I am asking for help. Thank you very much.

by csmith

Check the file
C:\WINDOWS\WIN.INI
The entry for a serial mouse on COM1 is
COM1:=9600,8,n,1,x
This entry is under the [PORTS] section.
If you have to correct this entry, reboot, before proceeding.
Next check Device Manager.
If OK, do a manual install, from Add New Hardware, and select Standard Serial Mouse.
Regards, Chris

by raquelmc

I checked what you told me, but the information in my comp is correct and despite of that doesn't work. Thank you very much.

by romancesar

Port IRQ
COM1 4
COM2 3
COM3 4
COM4 3
COM 1 is usually set aside for a Modem. Do you have any devices set on COM 1 or 3?? Try Com 2 or 4 like one of the suggestions earlier.

by csmith

What error message did you get on the Manual Install?
You almost had to have gotten an error message, when you tried the Manual Install, if the mouse still does not work.
What OS is installed?
From the age of the PCs it should be WinNT 4 or Win98.
Regards, Chris

by raquelmc

It just says that the driver is not correct, after installed the mouse is marked with the yellow exclamation. Win98. Thanks

by slogmeister

Have you tried having windows re-detect hardware? Sometimes it won't find the mouse automatically. You have to re-detect it manually. Have you tried re-installing the os with the mouse plugged in? Have you tried using the mouse through dos with a dos mouse driver? Have you tried plugging a modem into the serial port to make sure the port works? Have you tried using the mouse in another system? Have you verified the activation of the port in cmos? Do you have the latest bios upgrade for the pc? Let me know if any of thse work.

- Jason

by raquelmc

I tried all of that before and that's why I maked this question. Because after all that I did, I thought that perhaps there is something I don't know. Thanks

by dmiles

Does the machine have WIN 2K PRO installed?
BOOT.INI Switch
The /fastdetect switch,is usually set by default,disables serial mouse detection during rebooting.

by raquelmc

Operating system: win98. To everyone that reads this question: I already tried the mouse in all my IBM computers (7). I already tried 5 mice in the same computers. I tried with every serial port, and try manual detection of hardware, there must be something else but I don't know what. Thanks

by mark_sheard

What type of OS(Operating System) are you using? What type of mouse is it EG microsoft mouse or logic,compaq.? Does the mouse have a little switch from 2-3, as i know some mice do. HAve you tried other mouse drivers, the one that is compatible is the Standard serial mouse driver..

by raquelmc

win98, it does have a switch from pc to ms, and of course i have tried not only standard serial mouse, I have tried a lot of drivers even those that seemed almost foolish to try.

by karthikkumar

In your reply to answer 7 you have said that the driver list is followed by a yellow exclamation mark,which says the driver is incorrect.The most basic solution would be to check the website of the manufacturer of the mouse for a specific driver foryour mouse model.Try this too,install the mouse with a "standard serial mouse" driver in WIN98 CD.It works with all mice without need for specific drivers.If all else fails,check the serial port or mouse for hardware defects/problems or contact IBM directly regarding your problem.Let me know if your problem is solved.

by raquelmc

I have tried already with the suposed driver for these mouse. The problem is that it works fine in all my computers, except the ibm. Even the serial standard mouse works fine but not in the ibm computers, that's why I decided to ask. Thank you very much.

This discussion is closed to new replies.