Discussion Locked

Ultra 100 PCI controller card WIndows 98

0 helpful
19 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a i430 AT/ATX motherboard. I'm installing a new drive using a Ultra 100 PCI controller card. Originally I installed the drivers into an exsisting Hard Drive running Windows 98. Now I can't get the old drive to boot as well as the new drive. Itried a boot disk and the PC doesn't detect the floppy drive, (yes I have it set in the bios). The error I get is the device BIOS are not installed then it hangs. I've tried setting everything back to it's original state and now the original drive is detected although it doesn't get past the controller card script error. My files are still there. How can I uninstall the controller card drivers, or what do I need to do to install the Controller cards BIOS (If it won't recognize the A:\ drive?) I've fdisked the Master boot record, I moved the card into another slot to avoid IRQ sharing still nothing.
Any suggestions, recomendations, anything? HELP!!!

19 replies

by etoile

I bought the same card for my system and had similar problems. I resolved them by removing all cards from my system except the video card, added the Ultra 100 card and got it working. I then added the other cards one at a time, and found an IRQ conflict with my SB Live! card. I removed the SB, reserved the IRQ setting that the Ultra 100 card defaulted to in the BIOS, and then replaced the SB card and all others ... Voila! Good luck

by m.cothran

Yeah, get down to the basic's of your system "video, ram, cpu, 3.5 fD, Ide HD" Then reset your bios jumper. Make a new boot disk of another computer. Just goto Dos prompt and type in" sys a: "and then you will have a new boot disk. Ive had many go bad on me in the past. Look for your FD light to come one as system boots. If it still doesnt, check to see that your cables are properly installed. Refer to your hardware documentation for correct jumper settings, and pin alignments. ANd it sounds you may have to run a complete FDISK if the HD is unbootable. DO this after you boot of boot disk. Press shift F5 to goto into DOs. You must format C: right after you run fDISK and delete , and re create primary partition. But wait, you may be able to get into safemode, try that first, then a step by step conformation. Hopefully a new bootdisk and a bios reset will do the trick for your floppy drive. Let me know! Good luck -M.C A+ certified

by rebal

It's the original Hard drive not floppy drive that now cannot be recognize. thanks anyway for the other info I'm sure I can use it another time.

by dark force

The first thing that comes to mind when I read this...Are both drives on the same controller card?
The reason the BIOS isn't loading is the computer is confused, it doesn't know which IDE card to use. IDE controllers want to be the only one in the system. I would disable the onboard controller for the motherboard before installing the ATA-100 card. Then attatch both drives to the ATA-100 card.

This has nothing to do with the card's drivers, it doesn't sound like the machine isn't even getting that far.

Good Luck,
JR

by jimjennings

The BIOS may not recognize the Ultra 100 PCI controller as IDE. Try setting your primary boot sequence to SCSI and see if it will boot from the new drive. I would also switch the old drive to the secondary port on your IDE controller and leave the primary controller connection vacant.

by jdfcomputer

Just a quick thought.
In your BIOS, under integrated peripherals
did you disable the onboard IDE and assign a pci slot to the location of your ATA card?

Also try setting the boot sequence to try other boot devices if you have that option.

by schitzoid

The most likely prob with the floppy is that you have a connection worked loose, check the power, and both ends of ribbon. Happens all the time when adding cards. Is your boot sequence set to boot off of scsi? I know it's an IDE card, but you motherboard thinks its scsi! And yes, remove all cards but the video and disk controller, and in the bios choose reset dmi configuration disable anything you don't need. Not using USB, disable it! All your drives on the controller card? Disable the onboard! (you MIGHT need to use one of the on board ide channels for your CD.)

by paul d. masley

Beeb there, done that with a SE440BX. Remove everything from the PC except for the ram,video and hardrives. Make note of what PCI slot you are using. Go to bios. Change from IDE boot to SCSI boot. Reserve PCI slot under peripherls. shut down.Install floppy. Boot with good win98DE disk, no CD. If you can see drives. Great. Reinstall all cards. If you are using WIN98, it will ask for the ATA100 drivers first. Install them. Let windows fix the IRQ's. You should be ready to go.

Paul.

by mscoulter

OK, I just went through this...I have the answer but you are not gonna like it.
I wasted a lot of time troubleshooting and eventually the system was toasted to the point that it would not even restore from an ERU backup,which has always been infallable in the past. I tried deleting the driver files...I could give you the list but it will do you no good. There was a configuation incompatibility that I could not work out without a fresh start. Using a dos boot disk, I renamed the windows directory to winold...I renamed the program files directory to progold. I reinstalled win98 to a new directory named "windows" and rebuilt from there..I kept my root C files in place.
As soon as I had a fresh install of windows, I setup the ultra100 card first, then a legacy scsi ISA card for my scanner...then all the PNP cards. Now everything works beautifully, including the ATA100 card and the drive attached to it. Sorry that there is no easy answer, but if you go for this you will quit wasting time trying conventional troubleshooting methods that just don't work in this instance. I hope I have been clear and helpful...Feel free to email me with any questions. Good luck!

This discussion is closed to new replies.