Discussion Locked

Why can;t I enjoy my PC all the time?

0 helpful
15 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I'm the only user of my Shuttle SFF WinXPSP2 PC that I built a year ago. It's working great-have AV et al-no malware, no rootkits. My problem? When I shutdown my PC and turn off the surgebar switch, I don't know whether my PC will boot next time I try! Sometimes it posts and boots; sometimes the power and HDD lites are on but no post and no boot; sometimes neither the power lite or HDD lite come on and then I suspect power supply failure. I swear I do absolutely nothing to my PC between unsuccessful and successful boots! I always wait at least 15 minutes between tries. My Bios boot order is CDRom-HDD-Floppy. No CD or floppy is in its drive. When an unsuccessful boot occurs, my 19" LCD Proview monitor remains dark so there are no error messages. I'm open to suggestions, hints, or solutions.

15 replies

by cg it

humm you built it a year ago, it's working great "Except"!!!! you don't know if it'll boot the next time you turn it on.......

might be time to think about not building your next comp and get a Dell ???

by mallmill13

I neglected to point out that my problem began only 3 weeks ago; anyhow I wouldn't buy a Dell.

by mjd420nova

I've seen similar troubles from just about all types of machines, mostly home brews. The most common trouble is the connectors that are provided by the case manufacturer don't always match up with the connectors on the MOBO. some have an "always on" provision and some don't. Some have turn on functions at the keyboard, meaning at least the 5 volt part of the power supply be on, thus it is not really off unless you actually turn off the switch on the back of the unit. That means if you turn on the unit from the back, you get a flash of the lights but no power up. Then a keystroke will start the boot up. Check the BIOS for these functions. The reason for the change?? Who knows, I've got one that works the same way, and found it to be a failing hard drive that would keep the P/S from starting properly, thus no boot, Bios or any display.

by thechas

You say that you turn off the surge strip that supplies power to your PC.

While turning the strip off increases protection against surges on the power line, turning the AC power off may be at the root of your problem.

What I suspect is wrong, is that you have a weak CMOS battery. When the CMOS battery gets weak enough, it can cause the BIOS to lock up and not get through the POST process.

When you turn an ATX style PC off, some power is still supplied to the motherboard. Among other things, this power keeps the CMOS settings and real-time clock running.

When you switch AC power off to the PC, the system is forced to run the CMOS and real-time clock off of the back-up battery.

The coin cell batteries used for CMOS backup can last for up to 10 years "if" the PC is usually left with power on. When you turn the AC power to the PC off, the running life of the CMOS battery is significantly shortened.

To test this, try leaving the surge strip switched on and see if the PC now powers up normally after it has been off for a while.

If so, change the CMOS battery.

Chas

by animatech

When your PC is back up and running have a look at your eventvwr for any errors, Change your CMOS battery, run chkdsk on your system, go through logs on your PC see if you can find some sort of an answer, Change power supply, Open the box and have a look inside see if all cables connected securly, Clean the system and so on...
If it happens 3 weeks ago try to think if there was some sort of power surge, You installed somthing...

by rskcds

Your problem sounds similiar to what I've seen after installing a wireless keyboard. If your keyboard is wireless try connecting a wired keyboard before powering up.

by robo_dev

I would first unplug it from the surgebar and connect the PC directly to rule out a bad switch or other fault in the surge protector.

Assuming that your power switch is like most AT/ATX power switches, the motherboard is the one deciding to turn on the power supply, or not. The power switch is just a momentary switch connected to the motherboard.

The bottom line is that it is either the mobo,the ps, or the switch. As an extra test, pull/disconnect EVERYTHING except the processor, and try to power on. This would rule out a faulty component that was stopping the motherboard from going thru post.

The PS has multiple outputs 12/5/3.3V. HDD needs 5V and 12V. Getting HDD drive lights only would likely mean that they are getting only 12V...or the motherboard is stuck at the 'drive reset' part of POST.

See the following ATX power supply troubleshooting flowchart:
http://www.fonerbooks.com/power.htm

by mallmill13

Thanx to all who gave me leads to try. Frankly, I took all your advice to heart; my first solution was to leave the PC in hibernation so I needn't reboot. Too many electrical storms in Ohio to make that viable over the long haul. Finally, I tried another power supply [difficult with Shuttle as it needs both a 20 pin and a 4 pin mobo adapter]. I used a Compusa 250 watt ATX PS and connected it and let it stay external on top of the PC with case removed. It booted often and continually. So I ordered a Shuttle XPC PSU 250 watt upgrade from OEM 200 watt PSU. After I installed it, I found my PC starts without event always. Again thanx

This discussion is closed to new replies.