Discussion Locked

WinXP slowdown after tower transport?

0 helpful
3 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

After transporting my comp to school, I set it up, but it wouldn't boot ("could not load OS"). Starting in save mode it would hang while loading file 'agp440.sys'.

Took it back home, tried the Microsoft bug fix suggestion for 'agp440.sys' (http://support.microsoft.com/default.aspx?scid=kb;en-us;324764). It didn't help (safe mode just hung on a different .sys file). I was suspecting some OS files got currupted.

Booted from WinXP cd, pressed 'R' and ran chkdsk/r. It took a LONG time, found no errors.

I then reinstalled Windows XP. Windows started up, but it was VERY SLOWWW (it took 20sec for the start menu to open). I restarted, it was better but still very SLOW. I started backing up files to my other HD (transferring a 700MB file to my other HD took about 35min!). Burning a DVD took 2hrs compared to the usually 15min).

I ran hardware diagnostics tools such as PowerMax (both HD's are Maxtor) and Tuff-Lite but they claimed all was fine! I also ran HDD Regenerator v1.41 which does a physical surface scan (and recovery) for bad sectors. It scanned the entire drive and found no bad sectors!

I ran Defrag which found the HD to be rather fragmented. To Defrag the 80GB drive took about 8hrs! No improvement in symptoms afterwards.

Ran ScanDisk, which went through the first 3 phases but was VERY slow on phase '4 out of 5' (checking file data)...it took 5hrs to finish and found no problems.

I tested all my hardware connections. reconnected CPU, RAM, Video Card, IDE cables, even tried using a different IDE cable...made no difference!

Did a virus scan, nothing.

I think with all the tests I definetly ruled out the possibility of a bad Hard drive or corruption/bad sectors.

I'm running out of ideas!!!

---- My System:
P4 2.0Ghz 512K 400FSB S478
motherboard: ABIT BD7II ATA100
RAM: 512MB PC2100 266Mhz
Video card: ATI Radeon 9600XT
HD1 (OS on this one): MAXTOR 80GB
HD2: MAXTOR 120GB
OS: WinXP SP2 fully updated.
-----

HELP!!!

3 replies

by dmiles

I would suggest that you open the case and check all your cables are fited properly and while the case is open check the memory modules are seated properly,caheck all cards inserted in slots

If you have the back up as mentioned,then you could start over with a fresh install.

by panzer_ace

FIXED!

I formatted and did a clean install of Windows...and all was good! Just proves that often formatting is the best (and easiest) fixing method.

I still have no idea what was wrong with it specifically (software problem for sure though). Here's my theory: When I brought it to school I guess all that shaking somehow managed to corrupt a few system files on the HD (that's why windows wouldn't start). After I reinstalled windows I guess those files were over-written but something else got messed up (drivers, file system, swap file...we'll never know).

Suggestion for similar problem of this type:
1. Do a virus scan, defrag if you need to.
2. check all hardware connections (especially IDE cables) and restore your BIOS setting to default.
3. check Hard drive for problems (ScanDisk or physical surface scan using programs like HDD Regenerator to find bad sectors)
4. If neither one helps, back up your data, format the drive and do a clean install of windows
5. If the problem still presists, well then there is something for sure wrong with your hardware. Try using the hard-drive in another computer, basically do a process of elimination until you find the culprit.

Thanks for all the help and suggestions everyone!

This discussion is closed to new replies.