Question Locked

Wireless Connection Problem

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have an unusual problem. I reinstalled XP Professional on a Used IBM ThinkPad T40. I used an XP disk, not any IBM software. I also installed a Broadcom internal Wireless-G mini PCI card. I have all drivers installed, no missing ones.

Now my problem, when I boot the PC the wireless card will connect to my ActionTec wireless router. I am using WPA-PSK, and the ActionTec assigns an address with DHCP. I am letting Windows manage the connection.

However, if I do a repair or the wireless disconnects for any reason the wireless card will not reconnect. It sees the ActionTec, but stalls at the "Aquiring IP Address" step. It will not connect no matter what until I re-boot!

Any Ideas?

11 replies

by nepenthe0

Check the signal strength by hovering the mouse over the wireless network icon in the system tray. If the signal strength is low, that is the most likely reason.

Wi-Fi is short range 2.4GHz radio, essentially worthless beyond 150 feet from the access point. Here are some tips that may help reduce dropped connections with your laptop:

1) A vertical booster antenna for the router can enhance horizontal coverage by ~50%

2) If the router is located one floor up or down from the laptops, consider relocating the router to the same floor

3) If the wireless adapters are 802.11g, program the router to broadcast only in G mode

4) Enable SSID broadcast in your router setup

5) WPA encryption is more squirrely than WEP, but WEP is less secure

6) How important is encryption for your use of these laptops? If there are no likely snoopers within 150 feet, consider disabling encryption. With encryption disabled, connection is faster, data transmission faster, and there are fewer dropped connections

7) If you disable encryption, it would be wise to enable the MAC address filter in the router setup. Enter the MAC addresses of the wireless adapters, and the native MAC network card addresses of any desktop computers

8) If you disable encryption and enable MAC address filtration, periodically check for intruders. With Linksys, open the router setup, and navigate:

Status > Local Network > DHCP Client Table

The only MAC addresses posted on that table should be your own equipment. Any other MAC address is an intruder, and you can banish that person by adding that MAC address to the naughty list:

Wireless > Wireless MAC Filter > Prevent PCs listed below from accessing the wireless network

9) check for 2.4GHz radiofrequency interference near the laptops (cordless telephone base stations)

10) check for RF interference (fans, motors, hard drives, etc.)

11) check for shielding (metal cabinets, etc)

12) If still no connection, try disabling the Windows driver and enabling the proprietary wireless chip driver.

13) Be sure that you have enabled [i]automatic[/i] configuration for DHCP in your router setup.

That about exhausts my suggestions. When I have posted these suggestions in the past, TR members have jumped all over me regarding disabling encryption. You may legitimately [i]need[/i] encryption, but be aware that there is a penalty to pay for the complexities of this technology.

Again, if there are no likely snoopers within range of your access point, and you utilize MAC address filtration, and you are not overly concerned about the sensitivity of the wirelessly transmitted communication, your wireless connection will be more predictably successful by disabling encryption.

Rick/Portland, OR

by deanhancy

Thanks for your excellent suggestions. The problem is not strength. The wireless strength is high, other PC's have no problem connecting. The problem occurs with other wireless routers.
This particular PC will be used in a crowded Condo community and I would prefer using WPA.

It has to be in the PC software. I wonder if when I do the "Repair" some error occurs in the TCP/IP stack and the PC no longer accepts the DHCP protocol packets from the router. How can I test this and fix it?

by older mycroft

Have you tried powering-down the router ?

Powering right down. Waiting at least one minute then powering up the router on its own.

When the routers lights all turn green, THEN power up the PC.

I've got two towers that are hardwired along with a wireless laptop - sometimes I find that simply doing a 'repair' is not quite as effective as cycling the router by switching off then back on.

by nepenthe0

Determine whether encryption is the culprit by disabling it. If the problem persists, you have exonerated encryption.

Rick/Portland, OR

by deanhancy

Laptop reconnects just fine when no security is used on router. The problem has got to be in the laptop (IBM T40) I have tried installing the latest Drivers for the wireless PCI Mini card to no avail.

PS I tried power cycling the router, it did not help. This problem happens with any router running WPA-PSK.

by deanhancy

Thanks for your help. I have XP SP3 installed with all Optional Hardware updates.

I am wondering about what the Disable is doing when I run a "repair".

If I just "disable" the wireless connection then "enable" the connection it won't aquire an IP address.

If I then run an "Ipconfig /all" I get this:
"An internal error occured: A device attached to the system is not functioning."
"Unknown media status code".

by michael kassner

Did you have this problem before SP3? There are many issues presenting themselves after SP3 has been installed.

by deanhancy

I finally fixed the problem! Not to my satisfaction but the darn thing works. I kept noticing that every time I did anything with the LAN Ethernet connection it would "Disable" if the wire was unplugged. This would then cause the reconnect/repair problem with the Wireless connection. I finally downloaded the driver for the wireless card from Gateway since my gateway laptop had the exact same wireless mini-pci card. That seemed to ignore the LAN Disable problem and was/is always able to repair/reconnect to any wireless router running WPA-PSK!

by michael kassner

Glad to hear that and thanks for letting us know what fixed it.

I was curious as to if you have both the wired and wireless network adapter active at the same time or are trying to do that?

This discussion is closed to new replies.