Question Locked

Xp workgroup - 4 well behaved computers and one laptop which wont't connect

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

This is driving me crazy.
I have a XP workgroup setup with 4 computers (2 desktops + 2 laptops) each sharing drives and seeing each other no problem. I have a common user id and password on all machines.

I have a new laptop (XP pro) which I have added to the workgroup.

When logged on with the common user id and password it can be seen by all other machines and its shares accessed. The new laptop can see all other machines in workgroup and access the shares of them all bar one. When I try to access this particular desktop (again XP pro) a 'Connect to..' dialog box comes up asking for user id and password. No matter what I put in there it seems to ignore it.

I have tried vanillaUserId vanillaPasswd, thedesktop\vanillaUserId password.

What I don't understand is why it prompts like this when none of others do? And how can I get past it. I have tried using the network wizard to make it part of the workgroup, and have also checked the local security stuff against settings on old laptop to make sure they are identical.

Help please!

9 replies

by sgt_shultz

hmm. maybe some clues to be had in the security log on both boxes especially misbehaving one.
also perhaps try: workgroup\accountname
this sure sounds like permissions. have you checked to confirm they are the same on the drive and share on this box as the ones that work?

by sgt_shultz

You Cannot Connect to Other Computers After Running Network Setup Wizard
View products that this article applies to.
Article ID : 823305
Last Review : June 23, 2005
Revision : 1.2
SYMPTOMS
After you set up a home network using the Network Setup Wizard, you cannot connect to other computers on your network. The other computers do not appear when you click Entire Network to see all of the domains or computers on your network.
Back to the top

CAUSE
The Network Setup Wizard created a network bridge between the IEEE 1394 connection and the local area connection.
Back to the top

RESOLUTION
To resolve this problem, disable and then delete the network bridge. To do this, follow these steps:1. Click Start, right-click My Network Places, and then click Properties to open Network Connections.
2. In Network Connections, right-click Network Bridge, and then click Disable.
3. Right-click Network Bridge again, and then click Delete. Click Yes to confirm that you want to delete the network bridge.

Back to the top

STATUS
Microsoft has confirmed that this is a problem in the Microsoft products that are listed at the beginning of this article.
Back to the top

REFERENCES
For additional information, click the following article number to view the article in the Microsoft Knowledge Base:
283429 (http://support.microsoft.com/kb/283429/EN-US/) HOW TO: Prevent the Network Setup Wizard From Creating a Bridge in Windows XP

by malcooke

Thanks for the help so far. Both machine have clear security logs. Did try workgroup\accountname also but no good. Other message hints that logons may be cached so might be always using the cache logon entry which might be incorrect (maybe because didn't use format computername\username or workgroup\username)

Still checking permissions.

by 1bn0

I get this error all the time at work if I try to connect or map to a drive share that I had already tried to connect to without entering proper credentials. Windows stores the connection via UNC even though you don't have access to it. When you try to access it aggain it fails because you already have a connection, so the second one fails.

Open an explorer window. Tools : Disconnect Network Drive.

See if it lists the problem workstation:

\\workstation\share with no drive letter associated. select the workstatio and disconnect.

Try reconnecting to share again.

by malcooke

I am interested in the caching idea for logons. Perhaps it cached an incorrect logon and uses that every time now instead of the correct one I'm trying to enter. The question is how can one clear such a cache if it exists?

by cg it

its a workgroup not a domain. Fast user switching is similar to cached credentials as well as logging on automatically.

chances are the problem is permissions if you get a logon box. If your 100% sure the permissions are correct for the user account being used to log on, try to create another shared resource as a test and see if the problem repeats itself.

by malcooke

Looks like this is working now and the only thing I can think that I've changed is on the desktop I unchecked the box for simple file sharing. Didn't seem to make any difference staright away but next morning when booted up all machines everything was working ok. This after some 5 or 6 weeks of frustration. Ah well they say a little knowledge is a dangerous thing but I'd like to have a little bit here.

by emmykal2000

hi,
The error you are expriencing is very common, it has happened to me so many times. the only way i have managed to sought it out is by:
(a) Disable the Guest Account
(b) Make sure the Account you want to access has Admin privileges.

This discussion is closed to new replies.