Discussion Locked

2nd Drive impairs system?

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

There was an old (1995) Western Digital-Caviar, EIDE 859 MB HD that I have added for backup purposes as a 2nd drive to my K6-300/64 MB with an existing Fujitsu EIDE 3.24 GB as primary master. The primary slave is daisy chained off the primary masterand connected to controller #1.
After CMOS autodetected the correct CHS values for drive #2 (CHS: 853/16/63), I started the machine and the monitor displayed the initial DOS-processor / HD data, followed by: ?verifying DMI pool?? for which the screen froze without reaching the POST. I rechecked everything: did a warm reboot, and the same message and frozen screen reoccurred. Hence, I?m unable to get to DOS to partition and format the 2nd drive. When 2nd drive strap and power cord are disconnected, the primary master starts up fine and goes right to W98.
One solution source said that sometimes a dissimilar drive manufacturer could cause this and to get another Fujitsu of any size.
Alternatively, connect the CD-ROM strap from controller#2 to the primary slave, and daisy chain the primary master, from controller #1, to the CD-ROM. Then configure the changes in CMOS.
Are these likely solutions to the problem? What else is there? Thanks for your response.

9 replies

by maxwell edison

Greetings,

Disable the DMIStart utility. You may have to do this without the 2nd drive installed, since it "hangs" before the POST.

1. Restart the computer. Press and hold down the CTRL key until the Windows 98
Startup menu appears, and then choose Safe Mode.

2. Click Start, point to Programs, point to Accessories, point to System Tools,
and then click System Information.

3. On the Tools menu, click System Configuration Utility.

4. On the Startup tab, click to clear the check box next to DMIStart.

5. Click OK. When you are prompted to restart the computer, click Yes.

Regards,

Maxwell

by csmith

Another solution is to plug the Western Digital into the Second IDE channel with No CDROM on the second IDE chanell.
Western Digital has a good hard drive utility as a free download on thier website.
I would download it, and run the diagnostics, to make absolutely sure that there is nothing wrong with the old drive you are planning to install.
If there is some virus, or other trash on the drive, the WD Hard Drive Utility also has Zero Fill, so you can wipe the drive.
You can then partition and format the drive with no worries.
Regards, Chris

by csmith

Another Warning, Many Fujitsu HDs when Master, have to have the "Slave Present" jumper installed also. (It is a second jumper next to the Master jumper, and before the Slave or Cable Select jumpers.)
The "UDMA mode enabled" on the Fujitsu can alsocause trouble.
It tries to force the IDE bus to run faster than the WD can tolerate.
There is software on the WebSite for adjusting this.
(If it is not on the USA site, try the Canadian site.)
Regards, Chris

by p.i.b

Probably a little obvious but are the jumper settings on Master/slave set correctly? Although I've never had probles its wotrth checking that the last drive, the slave id on the last connector of the IDE cable. I presume that you've not got a MoBo with a promise controller (UDMA 100?) as the older drive may not be compatible with this. Best guess though is to check the jumpers as the machine may think its got two masters and hence falls over. Hope this helps Paul B

by grandhighdruid

I know this probably won't help you, but in my years as a repair techie, I have been told that sometimes certain models of hard drives just won't work with other models. Sometimes, they can even be from the same manufacturer! I had two Western Digital drives in a system one time, and while they would work, the system seemed to have to fight with them to work properly.

This discussion is closed to new replies.