Question Locked

A disk read error has occured. Press CTRL ALT DEL to restart....HELP?

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

ok i have an older HP laptop...a compaq nc6000 series. recently the HDD went out so i purchased a new one. i plug in the hard drive, retaining the jumper setting, but then i realized my CD drive stopped working also.

I put the new HDD in another computer and installed windows to it using that computer. once i came to a booted desktop, i shut it down and put the hard drive back in my laptop.

i turned the laptop on, and it says "A disk read error has occured. Press CTRL+ALT+DEL to restart." i do so several times, but to no avail.

How do i get this thing to boot? or do i absolutely need to get another CD drive to install windows using my laptop???

Thanks in advance.

the HDD is a WD Scorpio Blue 80GB EIDE Drive. Remember its an older laptop so it doensnt have SATA.

17 replies

by rob miners

Reconnect the drive that you just loaded and fire it back up in the System that XP was installed in and do the instructions below. Someone suggested that it was best to startup in Safe Mode when you reconnect it to the Notebook.

1. Click Start, and then click Control Panel.
2. Double-click Administrative Tools.
3. Double-click Computer Management.
4. Click Device Manager.
5. Right-click each device icon, click Uninstall and then click OK.
6. Shutdown the PC.
7. Remove the Hard Drive and install it into the new PC.

Might be an idea to copy over the Motherboard Drivers and your AV while you have access.

by coreyx64

For the mobo and I can download the anti virus it's a free one. howeever when I plug the hard drve into the laptop it won't boot windows to even get to safe mode.

I think this is a BIOS issue also...whenever I go into the bios to make changes, they don't save. I will "save and exit setup" but if I go back in and look at them I notice they go back to the way they were. Right now it has HDD as secondary boot device. I'm trying to change it to primary, but like I said it just keeps resetting. Should I check for an update to the bios?

Also when you say to uninstall all devices in device manager...do you mean every single one in each category? On the system I used to install xp on it ... I didn't load any drivers so there were a bunch of yellow quesionmarks. Do I have to uninstall all the rest?

Thanks for the tip. I will try that and get back to you on the results.

- corey -

by rob miners

So you reconnected the new drive into exactly where you removed the old drive from. Is this drive identical to the one that was removed and the jumper settings are exactly the same?

When you prepared the drive and created the Partition did you make it Active and was this dive the only one connected to the Sytem when you installed XP?

Follow the instructions below to reset the BIOS defaults.

HP Notebook PCs - Error Message from the System BIOS is Displayed on a Black Screen Referring to 'Non-System Disk Error or Disk Error' During Startup or Boot on Vista PCs

Non-System Disk Error or Disk Error

While you have the drive connected to the Host System run these commands.

Insert your XP CD and when you see ?Press any key to boot from CD? press a key. Now wait for the XP installer to finish loading up and you will be presented with the option to press R to Repair.

Press R.
The next screen will ask you which Windows? installation you would like to log on to. Normally the following will be listed:
1: C:\WINDOWS

Press 1, then Enter to continue.
You may now be asked for the Administrator password. If you know this type it and press Enter. If you don't know the Administrators password it may be blank. Just press Enter or type your username and password.

At the command prompt type these commands:

fixmbr and press Enter

fixboot and press Enter

Wait until you are returned to the Recovery Console.

Once you are back to the Recovery Console remove the XP CD and remove the drive.

As for the BIOS I would be looking to find one of these:

HP Compaq nc6000 Series Battery - Cmos / Resume / RTC

by coreyx64

Amazingly enough with alot of hard work and patience I can manage to boot from CD ON the laptop only when I have a deskop IDE drive plugged into a USB adapter. However the hdd must be unplgged up until the inspecting hardWare config message. Setup then loads like normal copies file to the hdd that it RECOGNIZES, however when it reboots it gives me the disk reed error MSG.

I'm lost as to what to do now...I've tried eerything.

Oh and FYI the non system disk link u posted from hp gave me a 404 error. Can you repost it? It took me to hps site but it said the pAge could not be found

Thanks again,
Corey

by thumbsup2

... if Windows install is running and the HDD is unplugged until later on in the install process, Windows can't detect the drive, format if necessary and install the boot.ini and other needed files which create the bootable drive prior to installing the OS. So, of course you get a disk read error. In addition, the system may not be capable of booting to a USB drive. It's probably looking for a floppy and, not finding one, gives the disk read error.

You're either going to need to replace the optical drive or get a USB optical drive to boot from so you can install the OS while the HDD is plugged into where it should be, not through an adapter.

by coreyx64

I unplug the drive UNTIL I see the "press any key..." message. So it's only unplugged during the post/bios screen. Once the setup message appears I plug it back in. And yes the setup does detect it and copies the setup files to it. But upon reboot, it says disk read error.

by coreyx64

That is letting windows boot? Ideall you shud be able to install windows from CD and it should take right off. That's how it works on the other systems I've worked on. However I did discover something interesting:

as you probably know manufacturers put their "branding" all over the machine when they preindtall the systems. This includes the OEM info for my computer, custom help and support center, oem "firstrun" screen, and specifically for HP, the default account Is "HP_Administrator". On this system with the existing hard drive, none of that was present. There was no custom HS center, no HP logo or support info in My Computer > Properties, and the user account was "User."

This has made it dry clear that this has either been reformatted already or it had it's HDD changed. I'm extremely curious as to how they managed to make it boot ... ;)

If u need any more info just ask I can get it and post it Here.

Thanks ,
Corey

by balge

hi
reading back a couple of things here
If your BIOS settings are being lost you probably need a new CMOS battery, JH's second link DOES work, part number is -
maxell CR2016
If you installed XP off an ordinary - not Compaq - disk then there won't be any of the @brand' stuff you mention, may not be a recovery partition - you probably formatted the whole drive?
If you installed XP on another machine it will be setup to run that machines hardware - NOT your laptop -it won't recognise the hardware etc. etc.
You may be able to reinstall XP by doing in in place repair install but personally I would reformat and start again - after checking BIOS settings! - if as you say the CD is working now
hth
cheers

by coreyx64

The cd drive is bad but I just took a desktop optical drive and connected it to the laptop with a USB to IDE adapter. I was then able to boot from cd and when I was in the windows setup I deleted the partition and formatted the disc fresh ON THAT LAPTOP I didn't slave anything this time. It still gave me that message.

It was jackye first link that was dead not the 2nd one. And the CMOS battery is fine. A bios update took care of the saving issue.

Xp pro sp3 was installed using an original hologram MS disc not an hp recovery disc so it is a fresh install. I generally never like to so repair installs I like that starting off fresh feeling...like getting a brand new computer :D

Well yes the hp branding isn't on an original microsoft disc. I was talking about the original hard drive that was in this machine---that one still boots into windows without any problems. When in windows I checked and
Noticed that there was no HP branding so I was just noting to you guys that the machine HDD isn't original---it was oem installed outside of HP. nvm about any of that anyway.

The original drive which still works is a hitachi 40Gb EIDE drive. The new drive I'm having trouble installing windows on is a western diigtal scorpio 80gb EIDE drive. I've tried recovery console and fixboot fixmbr etc nothing works.

What options do I have left?

-corey

by older mycroft

In your first post you said "[i]recently the HDD went out so i purchased a new one.[/i]"

How can the old HDD still be working and still bootable if it 'went out' and you bought a new one? This entire thread has been about your difficulties to install onto the new HDD, because you had bought it on the basis that the old one 'went out'!

[b]What options do you have left?[/b]

Well, I'd have thought that was obvious - if the old HDD still boots why don't you CLONE it onto the new HDD, then boot from the cloned new HDD ? ;)

by coreyx64

that first post i had posted before i had torn the laptop in 2...discovering the drive was still good. so at that point i thought it was bad since the motor would not spin. later to find out it is working. i apologize for the miscommunication.

i ususally dont prefer to "clone" HDDs because I like the idea of starting off fresh. If i absolutely have to i will, otherwise i'd rather run a clean install of windows.

by rob miners

You can purchase a USB 2.0 to IDE / SATA Adapter Cable 80cm (Supports 2.5" & 3.5" IDE) that you can connect a CD/DVD drive to and intall from that or try the instructions below.
Download DOS.

http://ms-dos7.hit.bg/#msfv

Burn it to CD using Nero or similar.

Remove the Hard Drive from the Notebook.
Disconnect your Primary hard drive and any others from the System that you are going to use.
Ensure that you have an Active Partition on the Drive and it is formatted FAT32.
Set your PC to Boot from CD in the BIOS. Connect your USB HD and turn on the PC. Insert the DOS CD that you created and follow the prompts to install it to the USB Drive. When you have finished installing DOS shutdown the PC and reconnect the Hard Drive.

Restart the PC and reconnect the USB HD, now you will need to copy the I386 folder from your XP CD to the USB HD. When you have finished doing that, disconnect the USB HD and insert it back into the Notebook. Turn on the Notebook and you should end up with a DOS Prompt. Type in CD I386 and press enter. Type winnt.exe and press enter. ;)

Edit: to add

copy your AV and Motherboard drivers over to the drive before before installing XP. You will need them.

by coreyx64

I've already got an IDE data adapter (3 in 1) to USB. That was how I got it to boot from cd since I used a desktop optical drive.

I would get a USB cd drive but I'm trying to work with what I have for now.

why doesn't this computer like to install windows how All other ones do? Am I doing something wrong or is this laptop known for doing this?

-corey

by coreyx64

for whatever reason everythings working now. i booted it up this morning, and went into the bios and i noticed 2 changes:

it recognizes my USB attached desktop cd drive as a usb cdrom, whereas before it was not there.

Now the internal cd drive works.

i pretty much figured the issue was something to do with the bios. I was able to install windows XP pro SP3 per normal method and it now succcessfully boots to the new 80GB HDD.

thanks 2 all that helped.

This discussion is closed to new replies.