Discussion Locked

Asus A7S333 Motherboard (200 Points!)

0 helpful
20 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello techies! I'm having quite an upsetting problem. I recently built a new PC, tested all the components with another PC, Except for the processor and motherboard (because I was too peeved).
Anyways, what happens is nothing. I have everything connected, checked and double checked, but nothing shows up on the monitor when I turn the computer on. It doesn't even give me error beeps! I know the video card is fine because it works with my other computer, the speaker is hooked up right because that works wiht my other computer as well. I have contacted Asus and they haven't got back to me yet, and I'm on a very tight schedule (I NEED to have it running before Christmas). It drives me crazy sitting around for someone to reply to me. Suggestions? Solutions?
Thanks for your time.
P.S. It came in a retail box from googlegear.com, everything was intact, so I'm hesitant to say the motherboard is bad?
Real E-Mail is:
abcdefgRaziel_82@hotmail.com.fakedomain
minus abcdefg and .fakedomain
200 points to the person who can successfully help me with my dilema.

20 replies

by parvus1202

First, the power supply, see that it powers up, second graphics card see that it sits tightly, third, the monitor see that it works and has power, forth, the monitor cable from the computer, make sure it tighly connected and working. These are the first aid, second aid, which makes users shaky is your mobo and cpu, if they faulty, we cannot do anything, bring them back for replacements. Or go to motherbards.org, they encountered a lot of these problems from manufacturers and users, you can get datailed information from them.
Good Luck Man

by kinetechs

A few thoughts:

1) Make sure the Clear RTC RAM jumper is jumpered 2-3.
2) Make sure the switch on the back of the power supply is set to appropriate voltage setting.
3) Make sure the connectors between the power supply, motherboard, and siwtches are correct. Some motherboards have the layout printed on the circuit board and sometimes these don't match the manual.

Cheers!
~Sean

************************************************
NOTE - When closing your question, please
provide comments. - Thank you.
************************************************

by opatzg9

No beeps, try reseating the cpu in the 0 insertiion slot, sometimes they don't drop in and without the cpu you have nothing. you'll need to remove the fan, the lock down spring/bar and then lift the little lever next to the cpu socket. lift up cpuand gently put back in place a mere finger worth of weight should get it to drop in to get relocked by the side armiture bar. MAKE SURE YOU ARE GROUNDED AND STATIC FREE!!!! This sounds like the most likely suspect, seen it happen before and I'ld have to think no beeping would occur. good luck

by cg it

Gonna ask a question. When you say "what happens is nothing" when you flip the power swith on does that mean that the CPU fan, case fans, power supply fans DO NOT go on?

note: If there is power to the mainboard and the soft "power on" switch cable is connected to the apporpriate pin header and the switch is ok, the first POST is "Power on". If the problem is after that, then one has to know exactly what is happening or not happening no matter how trivial it may seem [not having the luxury of actually being there to watch what goes on].

by cg it

note: page 41 of the Asus A7S333 manual says that you should see something on your monitor after 30 seconds of pressing the on button. If not, there is a failure in the POST. Given that information, gotta know if the fans go on. That means that at aminimum, power is going though the board. If so, then opatz's suggesting of reseating the CPU would be the second course of action.

by cg it

note: I'm assuming that the case fans, CPU fans are connected to the mainboard pin headers for cpu and system fans. [some people don't use those but connect directly to the power supply]

by djent

This my seem to simple but when I assemble machines I always use contact cleaner on all connections, CPU, slots, power, drives and so on. Dirt and oxidation may not be visable and contact cleaner solves those problems.

by wim

Check the memory, had the same problem, it is probably a non compatible type.
look on the asus or kingston website witch RAM to use...

by thechas

1. The CPU itself may be bad. Socket A CPUs are rather fragile, and if there is excess preasure from the heatsink, they will crack.

2. AMD CPUs can be very finiky about clock settings.
Remove the CMOS battery, and the power cord for 1/2 hour or so.
Reconnect power, and see if it boots up.

3. Make sure that the video card is fully seated in it's slot.
I have had several combinations of cases and AGP cards where the card would not fully seat in the AGP port.
An AGP card need only be a couple 0.001" out of the slot to keep it from working.

3a. On a similar note, I had 1 AGP card that did not have all traces on all of the connector fingers. This card only worked in a few motherboards!

3b. I have 1 motherboard with a damagedfinger in the AGP socket. The system will not boot with an AGP card at all.

Try a PCI video card as a test.

4. Check for shorts between the motherboard and the case.
One simple way, is to place a sheet of thin cardboard between the motherboard and the standoffs.

5. Check the power supply.
Either use a known good supply.
Or measure the voltage between pin 9 (purple) to ground (black)
This is the 5 volt standby line, and should have 5 volts present all the time.

6. Pare back to a minimum system.
RAM, CPU and video.
If it boots, you may have a problem / conflict with one of the other cards.

Chas

This discussion is closed to new replies.