Discussion Locked

Bad sectors

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I would like to know how I can totally erase my hard disk drive and remove the bad sectors too? I want to have a clean drive again. I don't know how the bad sectors got there or the cause of them.

13 replies

by vinnyd

The simple explanation is that bad sectors are caused are locations on the disk that can not be read correctly.

The Scandisk program Complete test can mark sectors as bad.

Formatting the hard drive over again can sometimes fix bad sectors so they are usable again.

To get rid of as many bad sectors as possible, go to the Hard Drive Mfg. web site and get a low level format program. If they do not have one, I am sure you can find on on the internet somewhere.

The down side is this, youmay format the disk and get the bad sectors gone, but they may start re-appearing in a few days or weeks. If that happens it is time for a new hard drive.

by dmiles

The bad sectors could be caused by the drive going bad and you will not be able to totally remove the bad sectors.
You can try using scandisk and do a through scan with the repair option.
If you use Fdisk and reformat the sectors will be picked upand go through a long repair process which will disable the sectors from being accessed.
Norton's disk doctor may help,yet it is no guarantee that you will be able to totally wipe out bad sectors.

by csmith

Most Hard Drive failures are caused by overheating or vibration.
The only major cause of Hard Drive errors that causes sectors to be marked as bad, when they are not actually bad, is a failing power supply.
Open the case and check the location of the hard drive. Moving it to a cooler location should slow down the rate of failure.

Also, back up this drive at the earliest convenient time.
I have seen sudden total failure, when these symptoms started.
Regards, Chris

by csmith

True bad sectors are caused by the head striking the disk.
To see this, open an old 40 or 100 Meg Hard Drive that has failed.
The scratches and gouges where the head hit the disk will be obvious to the naked eye.
There is no feasable repair for this.
(The head is supposed to "fly" above the spinning disk.)
Regards, Chris

by daz'n'ash

Thank you for your answer, but unfortunately it didn't help me. I was finally able to remove the bad sectors and it doesn't appear as though it will fail anytime soon.

by jmatt

Go to the Hard Drive manufacturers site & download the free
utility that most have , to help you get your HD the way you want .
( Including ghosting , writing to 0's , overlay , low level
format etc )

Sometimes if a drive has been setup withPartition Magic or similar
it takes a write 0's to fix it.

Maxtor's is called MaxBlast ,
http://www.maxtor.com/products/DiamondMax/software/maxblast/index.html

Seagate's is DiscWizard ,
http://www.seagate.com/support/disc/drivers/discwiz_utilities.html

Quantum's is DiskManager ,
http://service.quantum.com/softsource/disk_docs/dm2000.htm

IBM have a selection ,
http://www.storage.ibm.com/techsup/hddtech/welcome.htm

Fujitsu's is OnTrack DiskGo ,
http://www.fcpa.com/cgi-bin/goFrames.cgi/support/su_drivers.html

Western Digital's is Data Lifeguard Tools ,
http://www.wdc.com/service/ftp/drives.html#dlgtools

Samsung's is ClearHDD Program ,
http://www.samsungelectronics.com/support/hdd/utilities/utilities_03.html

by daz'n'ash

Thank you very much for your answer. This helped me a great deal. I have been able to successfully remove all bad sectors from the drive.

by muddyknees

Old drives usually go bad.
If ur willing to lose all your stored stuff then u can repartition ur drive.
Create a diagnostic disk. Boot from it, then run fdisk. Make sure u partition the right drive if u have multiple drives. Delete existing partitions then create a primary partition. Then go on from there.
Good Luck!

This discussion is closed to new replies.