Discussion Locked

Bios boot problem

0 helpful
16 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Recently I upgraded my computers CPU from:
AMD Athlon 800mhz to 1.4 ghz. Upon attempting to boot I get a 5 second bios beep, after which the computer automatically shuts down.
The following is my system configuration:
M Abit KT7A-Raid
CPU AMD 1.4ghz
Video AGP 4x ATI Rage 128 bit 32 mb
Harddrive 2 IBM Deskstars 40 gig on raid
Floppy LS 120 Imation
CD-Rom LG 12x8x32
Memory 256 MB PC 133 SDRAM
I flashed the bios after the upgrade.The system workedfine before with the same configuration. However, even after reseating the originalprocessor I experience the same problem.
I appreciate any suggestion on how to restore my system.
Walter J. Mueller

16 replies

by dmiles

This could be a number of problems,one reseat the memory and make sure that it is seated properly
The power supply reset switch could be in reset mode and causing this problem.
The cpu may be causing the problem,which could be in conflict with the video card.
If you have access to another computer go to the amd web site and it will have a fix for cpu speed setting.
Start resetting cards one at a time to see what is causing the problem.

by walterjmueller

Since I have the same configuration than before the change, neither the cpu, memory , video card, nor the power supply should be the problem. Furthermore, getting a fix for cpu speed setting would not be helpful. If the system shuts itself of there is no way to apply it.

by rjmessenger

This could be a stupid question, but are you sure you used the correct Bios when you flashed it? If you have access to another computer, go an verify that you have the correct BIOS version and try to re-flash it.

by walterjmueller

Although the Bios flash seems to be the probable cause,there is no way to reflash it without beeing able to start the system since it resets itself after 5 seconds.

by donmars

My first suspicion is that the bios flash is the problem. Of course after reinserting the original CPU it gives you that same error because logically the bios is incorrect for that cpu also. Did you follow the instructions for flashing the bios carefully? Also You should have been instructed to clear the CMOS. This is an important step in the flashing process. Clearing the CMOS will remove any residual BIOS instructions that may have remained after the new BIOS have been flashed. You'll need tore-enter your personal BIOS settings required for your system when settings are returned to default by clearing the CMOS. If you did not do that then clear your BIOS and re-enter stuff! If the whole thing is screwed you wont be able to recover from a faulty bios flash outside of a new M/B or maybe you can obtain the firmware chips from the motherboard MFG. I hope its something less drastic than a bad flash session!

by donmars

How is a recovery diskette ever gonna work when the computer can't recognize any drive, let alone the floppy drive, because the bios wont work! remember what the bios does! The only alternative to a defective flash session outside of a new M/B (withthe chips) is working bios chips for that M/B. If you have a burner (not CD) and know how to use it you can reprogram the chip manually, however some M/B have soldered in chips so that Idea wont work. These motherboards usually have a special rom Recovery procedure that can be performed. This hinges on a special unerasable part of the flash ROM that is reserved for this purpose. Check your M/B web site for info if you confirm that your M/B has a soldered in ROM chip.

by donmars

How is a recovery diskette ever gonna work when the computer can't recognize any drive, let alone the floppy drive, because the bios wont work! remember what the bios does! The only alternative to a defective flash session outside of a new M/B (withthe chips) is working bios chips for that M/B. If you have a burner (not CD) and know how to use it you can reprogram the chip manually, however some M/B have soldered in chips so that Idea wont work. These motherboards usually have a special rom Recovery procedure that can be performed. This hinges on a special unerasable part of the flash ROM that is reserved for this purpose. Check your M/B web site for info if you confirm that your M/B has a soldered in ROM chip.

by donmars

sorry about the double entry. You might also be able to take the chip to a computer shop and they could burn a fresh program in for you based on you comp model and cpu. Or return the chips to the M/B mfg and they may exchange them at a small cost.

by butzmann

Seems to me that you shuld try going to ABIT's website and downloading a recovery diskette. I hope they should have it. Then you should be able to reflash the bios with older file. Hmm... they don't have the disk... Have you read their FAQ? -- http://www.abit.nl/eng/faq/kt7a-raid.htm -- it may be of help

P.S. There IS such a diskette in the Net -- can't remember where now...

by mskiproductions

There are 2 flavours of AMD processors, one with 200 Mhz bus, the other with a 266 Mhz bus. It is likely that the 800 Mhz had a 200 Mhz bus, in which case, the memory in your PC may be PC100 (100Mhz). If your new processor id of the 266 Mhz flavour, you will need to replace you existing memory with PC133 (133 Mhz) as AMD's processors work by using a bus speed twice that of your memory, your motherboard will see you only have PC100 and let you know this (that would be the beeps).

Hope this helps you in some way.

Matthew Shine.

ComputaCenter, Europe.

by jesselou

go back and reconstruct your computer again. while you are there clear your cmos for 2 minutes. examine your jumpers very carefully. then reseat properly your memory and expansion cards. configure also your ports connections and put it in their proper connectors. restart your computer and press ctrl-alt-delete when before post this will load your bios default.

This discussion is closed to new replies.