Discussion Locked

BIOS Password

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have a Dell Latitude CP m166st. Someone has passworded the bios. Dell has a master Password however unless you are the original owner and a have recipt number they won't give you the password. I am most likely the third owner of this laptop. Is there any way to remove the password in order to use the unit. One of the Dell techs suggested removing the bios battery and I did so and that don't work. Help

17 replies

by mageeone

I can't get to the dos prompt to run a program. Appreciated the tool information though. thanks

by grump

Security is the reason Dell would not give you the password.. In laptops it is difficult to remove the POWER ON PASSWORD..
So try this.. Remove the standard power battery and also the CMOS battery. Un plug the AC power cord. Leave the Laptop in this state for couple hours even overnight would be better.. turn on the laptop with out the batteries and see if it will boot. Then you may proceed with replaceing the CMOS battery and the Standard power batter..
This has worked for me, but in some cases has not... Good Luck!

by mageeone

removed all CMOS and res battery let it sit for 4 hours and used the startup proceedure as stated and I still have the password.

by diskaus

you could try this DOS trick
Exit Wiondows or reboot to the native MS-DOS mode, using the "Command Prompt Only" option from tthe Windows 9x startup Menu ( hold the shift key and F5 at the same timewhile yuor PC boots).
At the C:\> prompt , type DEBUG prompt, Now type:o70 2e which will show as -o702e at the DEBUG prompt. Hit enter then type: o71ff and HIT ENTER. Finally typeQ and HIT ENTER one last time, to quit Debug, back to the C:\ Now you are ready to reboot your PC, and press the appropriate key or key combination to acess your Bios Setup. You will noticethat the Password is gone.
NOTE: THIS ONLY WORKS WITH MS-DOS 6.00-6.22 AND MS-DOS7.XX [a.k.a.MS WINDOWS 95-98].
hope that gets you out of trouble :-)

by mageeone

It wont let me get to any prompt. it boots to the password prompt. I am unable to access any drive.

by mageeone

they have the answer if you want to spend a lot of money on it. The backdoor password did not work.

by diskaus

Try Booting from a Boot disk ( startup disk) , if you dont have one but have access to another system that is running the OS as yours you can create a start up disk there and use it on your system

by mageeone

the bios pasword will not let you get to any prompt. It will not read any disk prior to incerting the password.

by diskaus

If you cannot get to any dos prompt even with a startup disk then it cant be a bios password but has to be a windows password (if running windows)in which case i sugest you contact the OS supplier ( eg. Microsoft)

by mageeone

It wont read the start up disk. As soon as I turn the unit on it displays the BIOS information and goes directly to the password screen. It does this regardless if a floppy or hard drive is attached to the system.

by james

The only other thing is then to check your boards i.e remove all the casing.
There may be a jumper or a switch that has CMOS written on the PCB. If you short that it resets all the BIOS including passwords
Let me know how you get on

by diamond dan

hi mageeone,

wow, a lot of people evidently do not understand basic hardware, BIOS, and order of operations at bootup! ;)

Here is the deal: the BIOS password is stored on a EPROM chip. This chip needs a steady supply of DC to keep it's data refreshed, this is the reason for the onboard battery. If the chip loses all DC power, then the data on the chip will be lost. But it is not that simple, as the system board has capacitance. What this means is that even after removing the battery, there is still some DC current stored on the board. The power consumption of the BIOS chip is so little that the onboard capacitance can keep the information intact while you would change batteries (or even while you run to the store to buy a battery to change :) ). To completely deplete the current on the board you can either wait a long time (depending on the components involved it could mean days) after removing the battery, or you can remove the battery and then 'short out' the capacitance to drain the current. In this respect the previous poster is correct, you need to find the jumpers on the system board to do this. They should be near the battery (but they aren't always). It should say something like 'Clear CMOS' or 'CMOS battery'. Keyword again is "should be" (motherboard manufacturers are notorious for not adopting set documentation standards). If you find the jumpers, move the plastic pin connector so that it joins the two pins(that were previously not connected). This will drainthe current and reset the BIOS chip. Move the jumper back and replace the battery and restart. You will have to check your BIOS settings, as they will have reverted to the defaults, to ensure that your system is the way you wanted it. Then you will be good to go.

Cheers,
dan

by diskaus

Hi Mageeonewell there is only one thing left to suggest , that is it IS NOT a bios password , it WOULD have to be a windows password , having said that i know there is a way to clear it but i am not sure of the commands , you must be able to get toa dos prompt somehow though , maybe try an anti virus bot disk , if the system is not reading the floppy disk drive first then the boot sequence is probably set as C:, A:. It should be A:,C: that way it will read the floppy drive and consequently the boot disk . Try pressing the key or key sequence to access the bios , (usually the delete button is the most common , it should tell you on the boot screen) if you can acess the bios settings then it IS DEFINITELY a windows password you are hunnting. Ihope this gets you somewhere .
regards ,
Steve

by mageeone

it does not go through the complete boot sequence it goes directly to the password prompt. it will not read a floppy.

This discussion is closed to new replies.