Discussion Locked

Boot hangs up after drives detected

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I'm about to lose it. I bought a MB (MS-6117 v. 1.1), installed it in a case, put in 32MB of PC100 RAM, a 300 mhz PII processor, and a 4 GB HD. After the memory check and HD detection, the boot hangs.
The "energy star" logo disappears, the rest of the text stays, and the cursor moves to the line below the last line of text and blinks. I've let it set for up to a half-hour and nothing happens.
I have swapped out the RAM, the power supply, the HD, everything but the processor. I've put the CPU in another machine and it works fine.
Am I missing something? I can't think of anything else it might be... Help me before I kill it!!!

11 replies

by squirrel01

I don't know what a MB (MS-6117 V.1.1)is but if it is a new motherboard you must set the appropriate jumpers to tell it what the speed of the processor is. If the board is not set to the correct speed it cannot read the instructions from your processor. You can get this information from the manual or from the internet. Go to the motherboard manufacturers web site. I am assuming the hard drive has been partitioned and formatted with the system files.

by thehuman

I'm sorry, I should have mentioned that. Yes, a "MB" is a motherboard, the jumpers are correctly set, the hard drive is formatted ( a pull from a working system), and it won't boot from the floppy disk drive.

by poettone

I also agree with the first answer to some extent. True that you need to set the jumpers on the system board but usually if they are incorrect you will not even recieve a display of any kind, after all the system needs the cpu just to make post. I would check the bios to make sure that the drive is properly recognized and set properly. I know all this makes perfect sense but I would take it down (Again) and verify all the settings on the board again. I would also clear the cmos and then if that didnt do it, I would install the chip etc on the other "working board" and go from there. I know this may not solve the problem but I would love to get my hands on this one,,,,

Good Luck

by thehuman

I've rebuilt the system a couple of times, just to make sure I had all of the connections right (I stopped after I held the board in my hands and threatened it with death by sledgehammer). I haven't cleared the CMOS yet, but I have tried the chip ina couple of other systems (worked fine).
If I can't get it working, I might just send it to you.

by reeree

sounds to me like the jumpers on the hard drive and/or cd-rom are not set correctly. If they are both on the same IDE ribbon one should be master and one slave. If this is a western digital hard drive and is on the ribbon by itself there should be no jumpers on the hard drive.

by thehuman

I've tried with the CD-ROM hooked up and unhooked. It recognizes everything as the appropriate Master/Slave IDE 0/1 position, but after it does that, it stops. The hard drive has been a Quantum, a conner, and a Maxtor.

by mcarrara

From your postings you have changed everything but the motherboard. Could the motherboard be bad? Even if it was brand new, it could have been defective or damaged during installation.

by thehuman

That was my first thought, but I requested another one from the seller and it has done the same thing! The only thing that I can think of is that it's one of those little stupid things that you take for granted. I've even isolated the board from thecase by covering the metal standofs with electrical tape to prevent the possibility of a short. It's driving me nuts!!!!!!!! Oh, did i mention it's a computer I'm (trying) to build for my mother-in-law?

by yagar

MS-6117 V.1.1

I found this on the web

The most probable cause is using 2 pin CPU FAN and connecting it to CPUFAN1 connector, which needs three pin head connector. To cease from the problem, go to BIOS -- Special Features Setup, and set the CPUfan detected to Disabled.

Good luck

by thehuman

I got really excited when I read this, but when I checked, it's a 3-wire CPU fan. Thanks for trying, though...

This discussion is closed to new replies.