22 replies
by lilac22281 Accepted solution
by jfuller05 Accepted solution
by lilac22281 Accepted solution
by patb071 Accepted solution
by lilac22281 Accepted solution
to make sure that this one would be compatible. I was disappointed to know that I could only upgrade this machine to another Pentium 4.
I have never heard of thermal grease--thanks for the info and help.
by jfuller05 Accepted solution
Examine the new Pentium 4 processor and verify that all the pins are straight and ready to be plugged into the motherboard. If any of the pins are bent, carefully push the pins back into place by hand.
Shut the computer off and unplug the electrical cord on the back of the computer base from the power source. Then undo the screws on the back of the central processor unit (CPU) with a screwdriver and slide the case top off of the base. Lay the case down so that the motherboard is lying flat, even with the table surface that you are using.
Locate the Pentium processor that is in the motherboard. Remove the old processor by lifting the socket handle on the side of the processor until it is vertical to the motherboard and lifting the processor straight up until it is clear of the pin sockets and then take the processor out of the CPU. Do not lean on any parts connected to the motherboard while lifting the processor out.
Turn the new Pentium 4 processor over so that you are looking at the pin side and locate the triangle in the corner of the processor. You will use this corner as your orientation point. Line up the corner with the marking on the processor sockets on your motherboard. When you have the new processor in position, push down slowly and carefully to prevent any pins from getting bent or damaged.
Press the center of the processor and each of the corners to verify that it is seated properly in the motherboard. Close the lever on the side of the processor to lock it into the motherboard.
Slide the cover back over the computer base and secure the cover with screws. Plug the electrical cord from the computer back into the power source and turn the computer on to verify the processor is working properly. When you are satisfied, turn the computer off.
by lilac22281 Accepted solution
by ron k. Accepted solution
by lilac22281 Accepted solution
by willcomp Accepted solution
Exercise caution when removing heat sink retaining clips. They are plastic and become a bit brittle with age.
CPU is supported by motherboard but you may need to update BIOS before removing old CPU. You have an older Dimension 2400 and BIOS likely does not include support for a 3GHz CPU.
by lilac22281 Accepted solution
by willcomp Accepted solution
You will need to update BIOS. This version of BIOS is run from within Windows. See Installation Instructions.
by oh smeg Accepted solution
The 2.2 P4's had a FSB of 400 MHZ and if your replacement CPU has a FSB of 533 you'll need to confirm that first the M'Board will work at this frequency.
If it doesn't support this CPU then no matter what you do the system will not work.
Col
by willcomp Accepted solution
by lilac22281 Accepted solution
by oh smeg Accepted solution
Opening the case changing any Jumpers on the M'Board that may need changing and removing the CPU Heatsink. On one side of the CPU is a Lever that you push down prize away from the socket slightly and allow to lift up. With the lever up lift the CPU out of the socket.
Grab the replacement CPU and align it to the socket so that it drops in [i]there is only one way that this goes into the socket here[/i] and then press the Lever back into the Lock Position wipe the Top[i]Metal Pert of the CPU[/i] with a Alcohol Wipe to clean it and the Part of the Heat Sink that Contacts the CPU apply a thin layer of Thermal Compound [b]Silicon Grease[/b] though be extremely careful here not to actually touch the Thermal Compound with your skin as it will contaminate it. Use a Cleaned Screwdriver to spread the paste over the CPU and then refit the Heatsink.
The P4 CPU's had 3 Generic Heat Sink Fitting Types and then places like Dell had their own methods of fitting these so you need to proceed carefully and never force anything.
Be Gentle but firm and if required use a small Flat Balded Screwdriver to help remove the Locking Legs of the Heat Sink. After you have the replacement CPU fitted and the heat sink on start the computer and enter the BIOS and check that the CPU is correctly Identified. Save the changes as you exit the BIOS and your all set. ;)
Col
by lilac22281 Accepted solution
by cg it Accepted solution
by lilac22281 Accepted solution
by cg it Accepted solution
by lilac22281 Accepted solution
by lilac22281 Accepted solution
This discussion is closed to new replies.
Trending Hardware posts
Sort by Trending