Question Locked

Can you Use an internal DVD Player and a separate DVD Player/Burner?

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Ok so here's the problem. I bought a DVD player/burner (dual layer + and - R etc..) by LG for my father for christmas. I figured since I've been able to burn my home movies and other dvd's from my dvd player on my laptop to my external dvd burner at home, I could do the same process using his already existing internal dvd player in his home computer after adding the dvd player / burner I bought him. So we made the DVD player the master, and placed the DVD player / Burner as the slave beneath the master. Everything is connected properly. And the DVD player / Burner works fine, but the regular DVD player we had before doesn't. The mouse freezes and then the rest of the computer does until I take any DVD out of the player. But I have none of these problems using just the player/burner. Now we checked with friends who have two dvd players/burners in a similar setup like ours and they have no problems. However a techie we talked to said you can't do what we're doing. However how could our friends do it with the two burners? Any help would be greatly appreciated. Or at least an explanation.

P.S. Just to make sure I've made myself clear, there are two internal dvd players. BUt one is also a burner. I want to put a dvd in the one that is just a player, then burn it to the other internal dvd player/burner that will have a blank disk inside. One note is that the company that makes just the internal DVD player is Creative. But the internal DVD player/burner is LG.

13 replies

by toivo talikka

Have you checked that the DVD player and the burner do not have a hardware address conflict? If they are on the same IDE channel, the jumper at the back of the player and the burner must be either both at Cable Select, or one as Master and the other as Slave.

If the devices are attached to different IDE channels (cables), make sure that the jumper setting in the DVD player is not the same as the jumper setting in the hard drive if it is attached to the same cable. Both need to be Cable Select, or the hard drive is set as the Master and the player as Slave.

by deadly ernest

1. jumpers are correct - one as slave, one as master - forget cable select.

2. cable is plugged in correctly on both devices and the motherboard, pin 1 is the red line.

3. both are capable of using the type of cable you're using - that is 40 pin or 80 pin, which ever it is. I've seen some that won't work with 80 pin cable, rare but happens.

4. the power supply to the system is big enough. You get some very odd happenings when you push the limits of the power supply. If this is a low wattage unit, that could be the problem, not enough power to run both.

by joshuayoung9

Ok well from what I can figure the jumpers are all set properly. The red line is attached to the motherboard, and the DVD player is set as the master while the dvd player/burner is the slave. The Harddrive is on a separate connection. It could very well be the power supply. From what I understand it would take more power to run the dvd player/burner then the older dvd player we have. And therefore when I try to use the dvd player no dice. However how come I have no problems at all with the dvd player/burner?
Basically when I put a DVD into the DVD player, it slows down and the mouse jumps a across the screen. When I take the dvd out and close the tray all is fine.
Is there a way of finding out if the power supply is low wattage or high wattage unit? Freeware? Or a way I can inspect it?
One last note. When we replace the dvd player with an old cdrw unit it doesn't have these problems. But I assume the dvd player takes up more power. Just wanted to mention it though.

by deadly ernest

Power supplies have their voltage and wattage marked on them. 115v or 230v is the voltage and just refers to the type of current you should be using for it to work properly (I don't have that problem here as Australia is all 240v). Watts is the actual maximum amount of power the system can handle.

The wattage is shown in a number like 250w, 300w, 400w or 500w. Many older and cheaper systems have 250w power supplies and work OK until you start adding things, they're built to the minimal to meet the original system specifications. For a new system you need to start at 400w (mine is 500w).

The actual amount of power you need will depend upon the cpu type and what else is plugged into the system. Some systems run the monitor off the PC power supply, so that adds to the drain, in such a case changing the monitor to direct power or changing from a CRT to a TFT monitor will reduce the drain on the power supply.

by jamesatmaisonverre

Make sure the roms are on the secondary ide and the hdd is on the primary ide on its own.

by joshuayoung9

I think I might have found the answer. According to a Techie friend I called anything over 300 watts is great for a powersupply and what I want to do. But I checked the back and there is a small red switch that says 115, and if I switch it it's 230. Now I'm obviously a newbie but I figured this is the power supply settings and it suggests that it's a low wattage which is not good for what I want to do. Am I correct?

by jamesatmaisonverre

you will blow your motherboard and your power supply.That is in relation to european and american electricity input.You cannot set the watts,you will have to buy a new power supply,i recommend 400w

by joshuayoung9

So does the 115 I see on the red tab in the back of the tower mean that it's 115 watts? If so could this be the problem on why it doesn't play the dvd player correctly but plays the dvd player/recorder alright?

by deadly ernest

Internally computers run direct current from the external alternating current. Changing the voltage can cause major harm if you don't know exactly what you're doing or why - usually because you then plug it into the wrong power line.

Power supplies have their voltage and wattage marked on them. 115v or 230v is the voltage and just refers to the type of current you should be using for it to work properly (I don't have that problem here as Australia is all 240v). Watts is the actual maximum amount of power the system can handle.

The wattage is shown in a number like 250w, 300w, 400w or 500w. Many older and cheaper systems have 250w power supplies and work OK until you start adding things, they're built to the minimal to meet the original system specifications. For a new system you need to start at 400w (mine is 500w).

The actual amount of power you need will depend upon the cpu type and what else is plugged into the system. Some systems run the monitor off the PC power supply, so that adds to the drain, in such a case changing the monitor to direct power or changing from a CRT to a TFT monitor will reduce the drain on the power supply.

by joshuayoung9

Well I've got nothing then. The only thing I can figure is that it is the dvd player itself that causes the problem. Everything else seems good. When I have the cd burner in one slot and the dvd player/burner in the other there are no problems. it is only when I have the dvd player in one slot and the dvd player/burner in the other as the master. I thought initally it might have confused the computer because you have two dvd players competing. But even if that makes sense (which it might not from a technological standpoint), I can't find out how to fix it. Wish there was a program that could diagnose this.lol

by joshuayoung9

Thank you all though for your ideas. Any new ones will be appreciated. This has been a great help for me. Cheers

by deadly ernest

every electronic device has Gremlins running around (they're what make the electrons move), every now and then a radical Gremlin does things differently just for fun.

Having two optical devices does NOT confuse the system, I've done that successfully so many times it's not funny. I've even had a CD Burner and a DVD Burner on the same circuit.

The critical things are (as previously explained) make sure the cable is plugged in right with the number 1 pin in the right place on the motherboard and all devices; make sure the jumper settings are correct; and make sure the master device is on the end of the line (some motherboards don't like them in the centre); make sure they're plugged in properly (nice and tight); ditto for the power cable. And make sure you have a strong enough power supply.

When you swap the devices between slots, do you change the power plugs as well? It may be that the power plugs are also on the same power feed line, and the DVD in first spot takes so much power there isn't enough for the other. I've seen that happen a few times some years back, with high speed hard drives. Split them up onto different power line feeds (most power supplies have two or three or four with a couple of plugs each) and see what happens.

This discussion is closed to new replies.