Discussion Locked

Cannot register MAC address on my VDP 3 Video Door phone

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Dear All,
When I trying to enter the MAC address of VDP 3 Video door phone, during the registration process it say wrong MAC/IMEI. I am typing as it shows in the paper but still unable to do so. I am trying to connect to the device via Vest Home 5 application.
The reset of the device was made but again same problem persist.
Any advice?

8 replies

by kees_b

What is that "paper"?
What is "it" that says something?
What does the help/user manual of the Vest Home 5 application say about the IMEI?

by fatonp edited

The paper, I am referring to the sticker attached to the device which is also the same one inside device. Basically the MAC address is correct but cannot registered!
During the VESPA registration, a pop up appears and informing the MAC/IMEI is incorrect. Connect the vendor.
The VESTA Home app suggests the resetting of the device, which I did, but problem still occurs.
Thank you

by kees_b

- It's somewhat confusing that you write Vest, VESPA and VESTA, of which probably at most one is correct.
- It's unclear why that error message mentions IMEI. Can you explain?
- If you connect the device to your router, what MAC-address is shown in the router management UI?
- Did you already connect the vendor?

by fatonp

1. You are absolutely right. I have used three different names for a single application, which is VESTA. My apologies to that.
2. In order to use VESTA app you need to register, user name and other credentials and then you must add the the MAC address in order to continue since the application is requiring that.
3. I have not managed to connect the device to the network yet
4. Yes, I wrote email to the vendor and no response from their side.

Thank you

by kees_b

The first time registration on https://eu.vestasmarthome.com/Vesta/ (I tried in Windows) says:
"Please be sure your equipment has been powered on, and connected to the Internet.
Note: If you are about to setup VDP or BRPD as a standalone device, the process has to be done using mobile phone app."

Now you say you have not managed to connect the device (the phone) to the network yet. Since that connection is required, that could be the reason for the error message. So first do that,

by bers5 edited

Make sure you are entering the MAC address exactly as printed, using uppercase letters and no extra spaces or characters. Sometimes, devices list the MAC with colons (:) or dashes (-); try entering it without separators. If it still fails, contact Vest Home support to verify the MAC is registered correctly in their system.

by businessinpakistan1947

This usually happens if the MAC/IMEI is not entered in the exact format expected by the Vest Home 5 app. A few things you can try:

Double-check that you’re typing the MAC without spaces or special characters (some systems require uppercase, e.g., AA:BB:CC:DD:EE:FF).

Make sure you’re entering the device’s MAC address and not the serial number (they often appear close together on the label).

If the label is unclear, try checking the MAC directly in the device settings menu, or on your router once it’s connected to Wi-Fi.

Sometimes a firmware update is required before registration works properly—check with the manufacturer if an update is available.

If none of these work, I’d recommend contacting Vest support with the MAC address you’re seeing—they can confirm whether it’s valid for registration.

by sarahjane70260 edited

Make sure you’re entering the MAC address exactly as shown on the label — without spaces or special characters (e.g., use A1B2C3D4E5F6 instead of A1:B2:C3:D4:E5:F6). Also, confirm that you’re using the correct app version (Vest Home 5) and that your device firmware is updated. If the issue persists, contact Vest technical support — sometimes MAC registration errors occur if the device isn’t yet added to their server database.

This discussion is closed to new replies.