Discussion Locked

cdrom reading a cdrw

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I HAVE A CDRW THAT CANNOT BE READ BY MY CDROM IS THERE ANY WAY TO GET THE INFORMATION OFF THE DISK I HAVE NO BACKUP AND REALIZE THE CDRW DISK IS PROBABLY VERY POOR QUALITY. ALSO THE INFORMATION ON THIS DISK WAS COPIED ONCE BUT WHEN I OPEN UP THE FILE WTIH WORDPAD IT IS ALL GARBLED INFORMATION AND ONLY PARTS OF IT HERE AND THERE CAN BE READ. HELP PLEASE. TED

12 replies

by agiias

If CDRW was copied with your CDROM, your CDROM is reading the CDRW. Generally, when CDROM does not recognize CD format a drive not ready or access failed error will be reported. If possible, try CDRW in same make/model recorder w/same software that created CD. Perhaps wordpad is problem - try heavier duty word processor. Recently had to restore CDRW backup. 12 of 406 files were truncated or damaged in some fashion. Redundant magnetic backup made recovery efforts unnecessary. My conclusion at this point - data is stored as pits and lands(flats) in the recording layer of the CDR, CDRW. Reading interprets the relative size/duration of the pits/lands. If size /duration of pits and lands is incorrect, the data is lost.

by agiias

One last thought - pass CDRW through any/all available recorders/readers. The recording process is not exact, and most/all recorders/readers have a deviation/error correction utility. Your data may be within deviation/error recovery boundries a particular reader/recorder.

by buffalodan

data can be written to a cdrw in a variety of different ways.

Single session disc to disc....(direct copy of another cd...)

Single session image to disc...( data is collected into an image file on your hdd before writing to cdrw)

Multi session file copy...(just what it says, data is written to disc in multiple sessions) multisession is relatively new to cd recording technology...

Older CDROM drives will NOT be able to read a multi session CD. (say 24x and less).

Also, recording media is CRITICAL!!!!

Pits and lands in a cheap cdrw disc, will appear different under microscopic inspection, than pits and lands on a hi qual (TDK) cdrw disc.

Also, Pits and lands on a cdrw disc are distinctly different in appearance than pitsand lands on a cdr disc. (the nature of the foil layer is completely different)

One more point...recording speed is critical...hi speed recordings often invlove higher density cdroms. (700mb as opposed to 640mb) this can also lead to read problems in older cdrom drives.

I like the answer above that says keep trying different drives, (50x and above if possible)
until you find a drive that can read this cd...then re-record onto a hi qual cdr(not cdrw) disc.
at 8x or less too...

Good luck...

by sparky4

Just some background info:
A manufactured CD has "pits" and "lands" that reflect the laser differently and allow the drive to read the disc. A CDR disk has a layer of dye on it. This layer of dye has tiny holes burned into it by the write laser of a CDR drive. They represent the pits and lands of a regular cd, and reflect the laser light almost the same. most drives should be able to read these discs. a CDRW disc uses a phase change technology that utilizes a seperate laser in the drives. The laser changes the phase of the disc to represent 0s and 1s. It can only be read by a compatible laser in a "multi-read" drive. It cannot be used by older drives, and most audio cd players gbecause they do not have the appropriate laser. Multi sessiondiscs can be read by older drives, but normally only the first session can be read if the drive doesn't support multi session. It is quite possible that your cdrw was not burned properly. try it out on other computers.

by zaphodtwin

I think you have to use special UDF driver for reading of this CD-RW on your CD-Drive... - because as usual info on CD-RW has been written as to usual HDD not as to CD (for example by PacketCD not WinOnCD). Try another mode of writing and Good Luck!!!
But, if will not succeed then change your CD-Drive - it's awfully old!...

This discussion is closed to new replies.