Discussion Locked

changing motherboards

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Is there a special preparation procedure one should do before changing motherboards? I have XP and figured it will automaticlly adjust when it sees the new board. Is there a "safe" way? Any config files that maybe need to be deleted first?

Thanks

JJ

14 replies

by m.a.s. matrix

Only thing really to watch for is static and proper grounding of the MB. Make sure you have the right size screws and don't tighten them too much...just enough so that they are snug. You can leave the old MB drivers on the hard drive or you can remove them. Make sure your memory and processor will work with the new MB.

Have fun!!

by Member 32254067

you may run into problems. First rule of thumb, if your going to switch that harddrive to a new mother board your best bet would be to backup your data and reformat the machine reinstalling xp. This may save you from may headaches. I have dont this many times and come up with many different results. Your machine might not even boot into the os, or it might but have other problems in the longrun. If you can get it work, run sysprep on the OS so it can rediscover what is on the motherboard and properly make its configurations. Reguardless i would reinstall the OS if i were u.....I guess you will find out one way or another...

by opatzg9

I'd have to agree with the last person as well. When my motherboard went out on a computer and I wanted to replace it with a newer board I asked the techs where I bought the mb and they said there is no guarantee the two motherboards would read thedrive the same way so fdisking and formatting was always their practice and rule of thumb when changing motherboards. They also said it may work for a while before failing so in my case I backed up my software with the new motherboard but didn't write to the disk with other than the operating system cache.
Good luck whichever way you decide to go.

by wcp

One of the most dreadful things that could happen when you replace your motherboard (M/B) is Blue Screen of Death (BSOD).
Typically when the two M/Bs have same chipset, this happens less frequent and you may get away from the BSOD.
Before you replace the M/B, make sure you backup your data.
When the BSOD happens, you have three options:
1). Install Windows XP from scratch. This requires reinstalling all your software.
2). But sometimes, this is not the best way. You may have some software that may not be easily reinstalled.
In this case, you may try to reinstall Windows XP on top of the current one. If this works, all your software and data will be intact.
3). Follow the instruction from MS Knowledge Base Q314070

by jackjay

Will installing XP on top of the existing one rewrite the registry? Will all my softwear still have it registry links intact? I'm obviously trying to avoid reinstalling the softwear.

by keyboard kowboy

Sure fire way for no errors:

- backup current config/data
- fdisk/format drive
- install and configure new hardware
- re-install OS

by thechas

Here is a link to a Microsoft Knowledge Base Article on moving a XP installation to new hardware.

http://support.microsoft.com/default.aspx?scid=kb;EN-US;314070

Remove any spaces from the pasted link.

What I do when I move a hard drive to anew system, (that is basically what you are doing when you replace the motherboard) is to REMOVE ALL hardware from device manager just before I shut the PC down for the last time.

This prevents Windows from attempting to install drivers for hardware that does not exist.

For XP, you should add a couple more 'tricks' to the move:
Keep the same NIC.
Keep memory size the same.
Use the old hard drive(s)

The above is to help prevent a product activation event.
You can upgrade the hardware a bit at a time after the new installation is up and running.

I would also download and extract the latest drivers for all hardware.
Use a folder named drivers with a sub-folder for each hardware device.

If you re-install XP, the registry, and all updates are lost.
You can run the recovery console should you have any problems.

Chas

This discussion is closed to new replies.