Discussion Locked

Computer will not boot!

0 helpful
23 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a computer that will not boot. I turn it on and it just sits there, and the monitor
tells me to check the signal or no signal input. I am guessing this is the reason the
computer stops the boot up. Am I correct?
Should I replace the videocard?

23 replies

by dmiles

No this is due to the power save,because the computer is not functioning properly
Check,your power cords on the back of the computer to make sure that they are snug.
Reads like a power issue if you are not hearing the hard drive or fans running,make sure it is getting power.
Does the lights on the front panel come on
Also check the surge supressor to make sure that it is on

by lizzy

I don't know about the power save issue as in #1 answer, but I've had this happen several times. Sometimes swapping out the monitor or the monitor cable if detachable will help. You will need to turn off then on the monitor to get rid of the Check Signal Cable. Other times, I have swapped out or replaced the video card and this resolved it. I would try the least invasive steps first, as in monitor and monitor cable, then the video card with the original monitor attached. I thought power save was when the PC was on already, not when you boot up, but you can go to Control Panel>>Power Management applet and turn off the power save options. If by power save he meant that the monitor goes to sleep with no input, such as yellow light instead of green, turn off the monitor, boot the pc and see if it boots with no video output on. Then try turning on the monitor to see if you get the check signal cable again. Good luck.

by mbr2

I have swapped the video card, tried
a different monitor, let the computer try
to boot without turning on the monitor,
nothing has worked so far. The hard drive
sounds like it is going to start but
then nothing happens. The lights come on
and nothing else happens. I can't read
what the cause may be because the
monitor won't work, and there are no
beeps to indicate a problem. Any other
suggestions?

by zlitocook

Answer two is right replace the video card. If it's an on board video card go to the main board web site to see how to do this. If it's a video card remove it and put another in its place. You can buy a cheap on at any computer store use a pci one. Your computer will or should detect the new card. You did not say what O/S you are using. Also check you memory, if its seated good.

by bohicam1

When you turn on the puter, is the fan running on the back of the power supply? If the monitor was getting power from the system, you would not get the signal check. This tells me there is no power on the puter itself. The reason it can't be the video card is the fact that any system will let you boot into a mode where there are no drivers running and you are in safe mode.
Either the fan is siezed on the power supply and it burned out or the fuse on it is gone.
Good luck!

Mike

by lizzy

Another idea would be to use a different slot for the video card. If the one you have is an AGP and you only have the one AGP slot, try a PCI card.

by s_pryce

If the machine has power (lights, fan whirring) and doesn't provide a video signal, something is holding the machine down. The best way (IMHO) to try and find out what is as follows.
First, remove everything you can, disconnect mouse, keyboard, allcards (except video), disconnect all drives.
Turn it on - if you get a video signal, hooray. The M/B, memory & processor work. Turn off, add a bit back on and try again. Repeat untill a machine fails and you've found the dodgy bit.
Second, if the machine didn't turn on with only M/B, memory and video card. Reduce the memory to one dimm, or 2 simms. Try turning on again. Swap the memory around, try again.
Third, getting tricky now cos you need spare parts, try another video card, try another PSU, try another processor (careful of speeds).
Last thing . . its probably the M/B fault.
Hope that helps

by ciscofred

Sounds like a cpu fried or your motherboard is grounded. If you are not even getting into post and no beeps, change power supply out and replace cpu. that does not fix it try another motherboard. good luck!

by thee loopster

the samething happen to me and I came to find out that the proccesor got fried. hopefully that's not the case, but if you don't get any beeps or any other signal look into trying a different cpu or easier if you can check the one you have in a different 'puter. If you fix the problem E-mail me to see what it was.

by mbr2

It was a bad modem. I pulled out the modem and turned it on and it worked!

by jwdavis

I just had this same thing happen a week ago, and it was the way the IDE cables were plugged into the motherboard. One was plugged in the wrong way. It didn't match the other one. If they have a red stripe along the edge, that will help. Some don't really give you a good idea they go, so its a 50/50 chance whether it is on the right or the left.

by bv2

remove the video card and try to boot - if you don't get the "video card missing" error, then your mobo may be shot.

by michelinda

I once built a new one and had it do this. We had a data cable off by 2 pins. Check all your data cables. Try to disconnect as many as possible to test and make sure the ones left are DEFINATELY correct as far as right side up and that they are seated well and completely on the pins. Red wire to pin 1 (arrow on motherboard, or a small number 1). Usually red wire to powersource on hard drive or again look for the small number one. Good luck!

This discussion is closed to new replies.