Discussion Locked

"CPR" for HDD

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have a Seagate U4 Model ST34311A, Obviulsy, if you can answer to this question, everyone can solve a similar problem.

It?s a very common problem... my HDD is not working. The little motor is not working, I connect it to the computer with the power wires and... nothing... the computer can?t detect the HDD. There is no sound from the HDD, Obviusly I can?t get the information, because the motor is not running...

Do you know how can I rescue my disk?

I?m working on a friends computer... but I hope you can help me.

navanc@yahoo.com

9 replies

by cdobbin

Well if you can't get the platters to spin up I would say your drive is toast. Maybe try it on a different power supply(grabbing at straws) and see what happens. With old MFM drives we used to drop them when they stalled, from a couple inches above a desk and this would sometimes work, but I am not recommending you do that :)
Good Luck

by geroxx

Well I would have to say that you are in a bind. I would suggest that you get in contact with a Data Recovery business

http://www.cbltech.com/index.html
http://eco-datarecov.com/
http://www.drivesavers.com/

If you want to attempt to do it yourself there are a couple of things you can do. One,I have had luck with is getting another drive of the exact same brand and model. I then swapped the logic boards. Pulled the data off and then swapped the logic boards back. This will only workif it is a logic board problem. Another is to freeze the drive in your freezer for about 30 o 40 minutes. Then take it out and mildly tap it on the table on the four sides then install it and hope for the best. Sometimes the heads stick to the platter and this trick will sometimes break them free.

I do not suggest this course of action for everybody as you may end up eating your hard drive... I would suggest that if the data is very important that you contact one of the places above and have a pro do it.

If you are adventerous you can go to the download area of this site and there is a paper called "200 ways to revive your harddrive"

https://www.techrepublic.com/download_item.jhtml?id=dr00320000510jed01.htm

Good Luck.

Gary

Gary

by pschuvie

The first thing is to be prepared that the drive has died and that you may not be able to revive it or recover the data on the drive. A purchase of a new drive may be needed.

Here are a few links to visit and get information from in preparation for trying to revive the drive.

Seagate Troubleshooter checklist - this is an online tool to guide you through steps to perform in diagnosing the drive.
http://www.seagate.com/support/npf/disc_ata/flowchart_ata.html

Seagate Diagnostic Tool - this is a handy software tool that runs from a diskette to assist in diagnosis of the drive. I have used it on several quirky drives only to discover the drive was ok but cable was bad.
http://www.seagate.com/support/npf/disc_ata/flow_diagnostic_run.html

There is a download here at TechRepublic in the download center 200 ways to revive a harddrive that might be of assistance. It is a collection of suggestions from members on reviving bad drives to recover data - three basic groups - testit, freeze it, drop it. These have worked.
http://www.seagate.com/support/npf/disc_ata/flow_diagnostic_run.html

My beginning point would be to pull the drive from the case, unplug the data cable, change the power plug to one used for other drive in the machine that do work, "known good", and turn on the computer. This is to test if it will spin up. You may not hear "noise" as a really good drive should be very quiet. Place you hand lightly on the top and bottom of the drive and feel forvibration/spin. If it is spinning then the problem points to bad power,bad cable, bad interface, or incorrect jumpers. IF it is not spinning then either the drive is stuck, or the onboard interface has gone bad and time to review the download listor contact the mfg for possible replacement.

Hope this helps

by hotsticks5

Hello,
This exact same thing has happened to me! Now, I will attempt to give the most in depth explanation of what I did, that you should also do. Call up Seagate, and tell them that the motors don't spin. They'll either have you send the drive back to them and pull your info off of it or have a Seagate certified tech do it for you locally. If you hard drive is still under warranty, then they will service it for free, if not, then you'll have to pay a fee. But otherwise, you get your infor back! Good Luck!!

This discussion is closed to new replies.