Question Locked

Data on old HD data not recognized in USB 2.0 external enclosure

0 helpful
8 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

When my motherboard died recently, I took out the main hard drive, and just installed it in an external enclosure after fixing the PC (new mobo and CPU) I'm using other internal hard drives in the PC(2). Device Manager says it's working properly, and it got assigned a drive letter, but it does not read any data: Properties says 0 bytes.
My objective is to use my current Outlook Express on my internal hard drive to Import years of emails I really don't want to lose from the now-external hd. Can anyone tell my how to make the data on the external hd visible and accessible so I can do it? I'm using XP Home Edition.

8 replies

by ozi eagle

Hi,

Check that the externalHDD is jumpered as master. I have found that the cable select option doesn't work.

Also try installing the HDD to an IDE port, to see if it works this way.

Herb

by noranor

Hi, Herb: Thanks VERY much for responding. Here's my setup: 2 internal drives (one is C and D, and is the master; the other E, and is the slave drive), my 80 gig external hd now gets identified as H.
When I looked at the external H drive in Computer Management in Control Panel, it "saw" 30 gigs and saw that part as empty, but did not see the other 50 gigs at all.
I looked at the jumpers, and of the 5 sets of pins, the middle two (top and bottom) are covered by a jumper with a wire, and the top right jumper (counting left to right that would be top jumper #5) is covered by a jumper thingy, while the bottom remains open. Does that tell you anything about whether it uis jumpered as a master? Can it be set up as a master when my C drive is the master drive?
I dont want to repartition it because that will wipe out what data is on it. I don't remember if the 30 gig part is empty or not, or whether it was partitioned that way (I doubt it) but I DO know that there's plenty of data on there.
Hope you're still willing to help. I'd love to get back the years of email on there.

by sgt_shultz

did you make sure you imported the drive thru disk management.

by ozi eagle

Hi,

The term master (slave) does not refer to whether your disk is the main (with OS) or not. It refers to an IDE port that allows two drives to be connected to it, designated master and slave. The master drive should always be at the end of the IDE cable, because by being master there are terminating resistor inserted across the data lines to stop echoes. In the slave setting these resistors are disconnected.

An external USB caddy contains a USB to IDE converter, hence theoretically giving your two more drives, ie a master and a slave.

In my experience the caddies only work with the drive set as a master.

Most drives also have an automatic selection of master slave, called cable select (CS).

If the correct type of cable is used and the drive is set to cable select, then the drive on the end is automatically the master and the intermediate drive is the slave.

I can't comment on what your drive is jumpered as, because each brand is different. Check the label, which usually has a jumpering diagram. The orientation of the diagram might be a bit confusing, as the digram is backward to the pins. Locate the KEY pin, which is a single pin next to the jumper header, which has double pins.

Some drives have the jumpering printed on the circuit board, next to the soldered pins of the jumper header. The names used could be DS0 and DS1. DS0 is the master and DS1 the slave.

From your questions I gather that you are not familar with the jumpering, which I take to mean the you simply plugged in your new disks and they worked, ie the are set to cable select, as was your original disk, hence the need to jumper it as master.

Good luck.

Herb

by noranor

I'd love to say yes, and string a bunch of good tech specs together, but I think this is out of my depth. That is, I'm clueless how to do that. But I learned everything I know about PC's through experimentation, so I'm ready to go there if you walk me through it. Don't worry - - my ignorance can't bring your level down; but your knowledge can pull me up! Thanks, Sarge!

by noranor

Disk Management says
Layout: Partition
Type: Basic
File System (blank - no words)
Status: Healthy
Capacity: 31.50 GB
Free Space: 31.50 GB
% Free 100%
Fault Tolerance: No
Overhead: 0%
Patiently awaiting instructions, sir.

by noranor

Changed the jumper to the master position, according to your advice and the diagram on the Maxtor drive, and it worked like a charm! Thanks so much - you're the best!

This discussion is closed to new replies.