Discussion Locked

defecetd motherboard

0 helpful
4 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

hi to all..

i had a computer that unable to run. when i repaired it i found out that the motherboard was defected coz i tested all the peripheral being attached in the computer and it was function normally. my question is, can ask you a tips , how to trouble shoot the motherboard? is there any site that can help me to trouble shoot the motherboard?.

thanks so much..

your answers are highly appreciated

john

4 replies

by thechas

For an individual, the costs to even begin trouble-shooting a motherboard FAR exceed the cost of several dozen motherboards.

Many motherboard and system manufactures use 3rd party service firms to perform component level repair on motherboards.
Without a detailed schematic, and some specialized (expensive) tools, it is VERY difficult to analyze a motherboard down to the component level.

I do not know of any resource for motherboard schematics. This is in part from the complexity of thedesign, and the fast changing nature of the PC business.

Things that you can do:

Start with a thorough physical inspection under magnification.
You are looking for:
cracked solder filets;
corroded or damaged pins in sockets;
burnt or discolored components;
bulges in component bodies.

If you have training in electronic circuit theory, you can check the oscillators and power supply circuits with a good oscilloscope and DMM.

The equipment to remove and solder the larger ICs costs thousands of dollars.
Even de-soldering smaller components has a high risk as most motherboards have 4 or more layers of circuitry.

Chas

by tech_wiz03

As the chas already pointed out, you are beating yourself in the head trying to even attempt descrete troubleshooting. I have been working with pc's and computers since before the era of Pc's ie 1970 and i can tell you even with the most expensive equipment (inclusive of computerized logic analysizers and analytical symulators) you will stand at best a 2% chance of fixing a defective board. If you really want to try, get yourself the full set of jetec chipset code books, full set of pc fabrication and restoration books, a few thousand dollars of surface mount feedthru and pass through equipment so you can desolder and resolder without frying every chip on the board and pray.

Like the chas said it would be best to just spend your 45 to 290 dollars for a new motherboard.

regards Rick of All Tech Development

by dmiles

A. Try these steps:
? Disconnect the power cord form the power supply, be sure the power supply is set for 110 or 220 volts depending on your location and power and double check it (most have a 110/220 switch)
? Feel/look at the back of the power supply to determine if the fan is working.
? If not, trouble-shoot the power supply and replace it if necessary.
? If the fan is working, try another power supply anyway.
? Plug the computer directly into a known-good (a lamp works) power outlet
? Check to be sure you do not have a motherboard stand-off in the wrong position and shorting-out the bottom of the motherboard.

? Look carefully at the ISA and PCI slots, see if any of the contacts got bent/shorted-out. Sometimes an expansion board will dislodge one and it will be pushed into the bottom of the slot.
? Inspect the motherboard for broken or burnt components.
? Carefully inspect the motherboard for black soot from bad bearings and clean and replace the culprit.
? Look for bent/shorted pins on the motherboard headers and straighten.

? If not, double-check all jumpers.
? Push down on all chips that have sockets in attempt to reseat them.
? What CPU are you using? Be sure the core voltage is correct.
? Be sure the CMOS battery jumper is in the correct position. Some distributors purposely ship motherboards with the jumper in the wrong position.
? Find the jumper that clears the CMOS, put it into the clear position for several minutes, put it back in the normal position, plug-in the power cord, and push the power-on button. If you apply power to the motherboard with the jumper in the clear position you may damage the motherboard.
? Pull all boards except video.
? Disconnect all cables going to all drives, pull all cables except power, power on, and speaker, connect the power supply to the motherboard (the black wires go in the middle on AT power supply connector

? Reseat/replace the memory.
? Check the CPU for bent pins.

This discussion is closed to new replies.