Question Locked

Dell Dimension E521 (Jan 2007) was running ok until I upgraded to 4GB .....

0 helpful
27 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi, I have Dell Dimension E521 that I bought Jan 2007. Have been running smoothly until 2 months ago. About 2 months ago, I called Dell to buy a printer. After that, the sales person talked me into buying 4 x 1GB RAM (Corsair, XMS2, DDR2). The computer was ok for couple of weeks, then I installed the Dell printer V505. A week later I started to notice some problems.

First, it was Internet Explorer hanging, but I thought it's just IE

Then, after the welcome screen, the icons failed to show up (so it's just showing the blue screen, standard color for WIndows XP). First few times, after hard reboot (or unpligging the power), it's ok.

Finally, on Jun 23 (or so), it just refused to turn on ever (after the welcome screen). Tried diagnostic, nothing. Went to the computer shop, they managed to revive it (after uninstalling ZonaAlarm).

I then reformated the entire HD, reinstalled XP, all the drivers, installed ONLY the necessary software (NO ZoneAlarm). LASTED ONLY 3-4 days before IE not working. Tried to go to previous Restore Point, made the problem worse. Another blue screen (after the welcome screen).

Yesterday try the Repair XP (using disk from Dell when I bought the system), complete failure, just stop mid installation (screen: Restore Point, OK button, nothing happened when hit). Yanked the power.

Now, I'm at loss? What is the cause of the sudden problem? The printer? Or the gigantic memory I installed?

How do I find out if the BIOS can handle that large? Can I return the memory if that's the problem? Remember I did not plan to buy it, I was basically talked into buyin one.

Please help. I'm running out of ideas how to fix this computer (also running to time)

Thank you in advance!

27 replies

by thumbsup2

If so, put it back in. Sounds to me as if at least one of the sticks of RAM you put in is bad.

If you don't have the old RAM any longer, try putting in just 1 stick at a time (or two if they must be installed in pairs) to see if it works better.

As far as IF you can return the RAM... you'll have to discuss that with DELL. We have no say in the matter.

by namasamaran

I have not reformatted the HD with the old memory back. I'm in the middle of moving out of state with 2 boys in tow! The house is listed on the market and we need to "dissapear" from the house whenever prospective buyer(s) come. The weekend is always heavy (as heavy as possible with the current house market condition).

Will do sometimes tonight because my husband will need to use my laptop to formalized the new job.

Will update later

by older mycroft

Did you then go online at any point?

ANY computer that is online without a firewall (don't assume that Windows XP's firewall counts) has a matter of minutes (at best) before the system [u]could[/u] be riddled with infection.

I assume your 'necessary software' included an anti-virus scanner? ;)

by namasamaran

I did have the anti-virus (AVG Free) but NO firewall (only the XP firewall).

Are you sure that without any firewall, albeit with anti-virus, my computer will be infected that fast?

by oh smeg

Which is not fully compatible with your M'Board. But as you have 4 Modules of it try only fitting 1 or 2 and also try doing a Memory Test with Something like MemTest86

http://www.memtest86.com/download.html

By itself 4 GIG or RAM will not hurt the system but if it isn't fully Compatible or is Mismatched it very well could introduce Timing Issues or other problems.

However generally speaking Corsair RAM is very good so unless there is a major difference in the actual Modules or they have been damaged by Improper Storage or Handling they should work well enough that is of course if they are compatible with the M'Board of course.

but in answer to your Questions at the end

[i]How do I find out if the BIOS can handle that large?[/i]

Open the BIOS and look to see what is reported. If you have On Board Video like Most Dell's do whatever is set aside for the Video will not show so you'll need to add that in.

[i]Can I return the memory if that's the problem?[/i]

This is between you and Dell and whatever State laws are applicable but I would speak to Dell nicely/reasonably on this issue to try to resolve it as it is in their Best Interests to help you solve this problem, but of course if you jump on them they are quite within their rights to tell you to go away. ;)

Col

by namasamaran

How exactly you "open" the BIOS?

Open the physical desktop and see the printed text or try to go to Setup screen (F2 in the case of my computer).

BTW, another different question, why don't I have an option to Safe Boot? Some forums seem to suggest that it should be an option somewhere along the screen BEFORE the Welcome screen (usually F8?)

Thanks

by oh smeg

It allows you to open the BIOS/CMOS and look at the Installed Components as well as settings. You need to [b]Save the Changes[/b] as you Exit the BIOS to allow the system to set the New Memory. If you didn't do this the New RAM will not be getting correctly Mapped and could cause problems.

As for the Safe Boot Option you need to press the [b]F8 Key[/b] and I recommend holding it down between the time that the Makers Logo Disappears and the Windows Splash Screen Appears. So I suggest pressing and holding the F8 Key down while the Logo is on the screen till a White on Black Screen Appears and then using the Arrow Keys highlight the Safe Mode option and then press Enter.

Col

by balge

hi
your PC should be compatible with that RAM, check BIOS settings to ensure proper speed is selected (pc26400,800MHz) test it with e.g. Memtest - http://www.memtest.org/

or substution one stick at a time to check or replace with original to discount RAM problems
With there being a week between upgrade and problems it seems unlikely to be the cause unless the hardware has become faulty
Does the printer work?
check this lot for |Dell diagnostics

http://support.dell.com/support/topics/global.aspx/support/dsn/en/document?c=us&dl=false&l=en&s=gen&docid=A9E3A15597A04AFBB02EE16785D39C5C&doclang=en&cs=
cheers

by namasamaran

Hi printer works fine.

Now that my PC is completely busted, I guess I need to re-install XP before I can do any memtest, right?

Now the question is re-install with old memory, or new one (all 4 or only 2).

You're right, that fact that the problem does not show up few days later, maybe it's not memory chip itself (physical) but more like a conflict of BIOS/jumper/etc (now I'm talking jibberish here, I'm not a computer expert here, just stay at home mom)

Thanks

by balge

hi
well if you have another PC you could download the iso.zip, unzip it then burn a CD, the CD should boot the PC then you can test the RAM
Easiest is put known good sticks in - because you know they are good
As you say reinstalling is more important as we dont know if the RAM is duff or not
personally I would clean install -

http://support.dell.com/support/topics/global.aspx/support/dsn/en/document?c=us&dl=false&l=en&s=gen&docid=E6480205F57CFE57E030030ABD627EAC&doclang=en&cs=#1

unless you need the data particularly.
otherwise try - http://support.dell.com/support/topics/global.aspx/support/dsn/en/document?c=us&dl=false&l=en&s=gen&docid=26B720E7D596B89DE040A68F5B280867&doclang=en&cs=#1

http://support.dell.com/support/topics/global.aspx/support/dsn/document?c=us&l=en&s=gen&docid=3E48AE3870775D64E040A68F5B2877D4&journalid=6E09F494F17D12C4E040AE0AB6E1227E&Query=&SystemID=&ServiceTag=&contenttype=&os=&component=&lang=&doclang=&toggle=&dl=
let us know how you go
cheers

by namasamaran

Are you reading the other answer to my question, or only the reply to your suggestion?

Just in case: please read what I did last night and this morning.

https://www.techrepublic.com.com/5208-7343-0.html?forumID=101&threadID=312648&messageID=3111729

I did the reformatting and plan to do the same steps from last week. Not sure if this is a smart move. The only difference will be the fact that I had run the Memtest, which, I think, a PASS for the memory chip.

Oh here is the result from the Memtest:

Sempron (0.09) 1804 MHz
L1 cache: 64 kB 14091 MB/s
L2 cache: 256 kB 3522 MB/s
L3: NONE

Memory: 4031 MB 2485 MB/s
Chipset: AMD K8 (ESC: Disabled)
Settings: RAM: 451 MHz (DDR 902) / CAS: 5-5-5-18 / DDR2 (128 bits)

Does this mean that according to the Memtest, the speed for the memory chip is 451 MHz (as opposed as the 800 MHz reported when I did F2, see my other posting)?

Please advise further....

Thanks

by balge

hi
ref speeds, the RAM is capable of higher speeds than your PC could handle, but should run at your PC's best speed automatically - if the BIOS tries to run them too fast it can cause lots of problems - but from your other post BIOS seems to have it right, Memtest is saying the the possible top speed of the RAM is all
Otherwise the only possible problem is the 'Dual Channel' mode - possibility of problems with some hardware, however if there is still a problem, you should be able to turn Dual Channel off in the BIOS
whew think thats up to date now
did you boot it up yet?
cheers!

by namasamaran

I did F2 but not much reported under BIOS:
System Info: Dimension E521
BIOS Version 1.1.4 (12/09/06)
Processor: AMD Sempron Processor 3400+
Clock Speed: 1.8 GHz
Bus Speed: 800 MHz
L2 cache: 256 kB
Processor ID: OFF2
64-bit technology: yes

Memory: Installed: 4.0 GB
Speed: 800 MHz
Channel Mode: Dual
Memory Tech: DDR2 SDRAM
Then a table with info for each momory chip:
Memory Slot, Size, Ecc (all No), Rank (all 1), Type (all unbuffered), Organization (x9)

QUESTION: Can the BIOS handle 4 GB?
Since it's reported installed memory of 4 GB, does it mean, the BIOS recognizes it?

Last night, ran the Memtest86+, no failure. Does that mean that the new chips are physically goood?

Just did reformat of the HD WITH all new memory installed (this morning), will proceed with installing drivers and minimal software.

QUESTION: Should I upgrade the included IE6 to IE8, or should I hold of until I know that the system is running (meaning: is it possible that IE8 crashed my system, before all this problem I was running IE7)

QUESTION: How about Google Chrome?

Thanks

by balge

hi
think I may have cross posted somewhat..not sure where we are so Ill answer this first
>Can the BIOS handle 4 GB - yes, it seems to be happy with everything there, speeds OK, if Memtest passed them all (RAM) then they should be fine - did you test all four at the same time then?

>Should I upgrade the included IE6 to IE8? get it running first if it boots after your reformat then its sorted - could IE8/ MS update have caused problems? oh yes, easily..
as to Chrome I use almost exclusively on Windows boxes - because IE8 has been so flakey, plus Chrome is really fast and simple

have you got PC to boot then?
cheers..

by namasamaran

I did the Memtest with all 4 chips in (standard test) it took a while, so I left it on at 1am, pass all test in the morning, but the Memtest is still running, and repeating the test??, so I did the Esc button (it was written at the bottom, all tests pass, press ecs to reboot)

I just did the reinstallation of the OS, in the middle of installing drivers. Oh what a slow process!

Plan: After the driver, will do the MS update (to SP3, from SP2), get the AVG Free, ZoneAlarm Free, installed MS Office, then I will just wait for a couple of days.
Will stay with IE6 for a while

Sound like a good plan??

by namasamaran

Tried F8, can not go to Safe Boot mode?
Any other way?

The F2 setup under Fast Boot is On: Boot Quickly.

Should I change it to Off?

by oh smeg

Sorry but it has to work as this is part of Windows. It's not like the BIOS where you press the F@ Key and are taken to the CMOS Setup Pages you have to wait with the Key held down till the screen appears. But if the Windows Splash Screen with the Blue Moving Bar at the Bottom Appears you didn't press the F8 Key soon Enough so you need to repeat the process, and press and hold the key down earlier. I show people to hold the F8 Key down till the internal Speakers start going Nuts and then to release it and wait for the Different options.

As for the Fast Boot Option this will not hurt anything at all and will speed up the time that the POST takes [i]Power On Self Test.[/i] So leave it switched on.

Col

by namasamaran

Ok, yes, I did not hold it long enough. Last time I just pressed it repeatedly until the internal speaker started to beep. Obviously it was not enough.

Thanks

by namasamaran

Separate question but maybe the cause of my 2nd installation problem:

After I reformatted the HD, I need to run the Dist containing Dell driver utilities (one by one!). Each of them requested to unzip files to certain folders.

QUESTION: Can I safely remove those files after the installation (I do not like to have setup files sitting unused in my hd), or those files are used all the time (part of the execution of the drivers)

Thanks

by balge

hi
you can remove the .zips after you have installed the programs is that what you mean?
otherwise I wouldn't go deleting stuff until you up and fully backed up
cheers!

by oh smeg

In the Root of the C Drive are perfectly safe to delete. Just [b]Do Not[/b] Delete any Folders anywhere else like in the Windows Folder.

Col

by namasamaran

Yes, those files from the unzip files from Dell Drivers CD.

Thanks

by oh smeg

When you upgrade from IE6 and on a clean install. If you had IE7 and then go to IE8 things are just downright flaky.

I personally download things like SP3 and IE8 so I don't have to waste lots of Bandwidth downloading them over and over again not to mention that it's also much faster to install them from a File than it is to download Install and reboot. If you think that adding the drivers is a slow process you have yet to experience Updating the System. I have Slipstreamed SP3 to a Install Disc and after that is loaded and Office with all of the Service Packs installed I still have several downloads well in excess of 150 MEG to install. I see this as a complete Joke needing to install just about as big a Updates as the Original OS took but I may just be Cynical. ;)

In answer to all of the other questions Yes the BIOS can correctly see the RAM as it is showing it but you do need to Save the Changes as you exit the BIOS or the system will most likely still think it has the smaller RAM Load and not be mapping the installed RAM correctly.

Lets know how you get on with the new install.

Col

by oh smeg

As there are 4 Sticks of the Same RAM involved here so the system should work in Dual Chanel Mode and allow better performance. ;)

Col

This discussion is closed to new replies.