Discussion Locked

disable sound card

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I have a compaq presario 7360 running windows 2000. I had no sound. I had help getting ESS Allegro PCI audio recognized as running on computer, but still, no sound. I purchased a new Magic Sound PCI sound card. It is compatable with 2000. I also bought a new MPCII cd-rom cable to run from cd rom drive to new sound card. Installed the hardware but the software will not fully load because I am not sure how to disable original sound card that cannot be removed. I tried going to device manager and clicking disable on the old ESS Allegro but when I try to install the new card with sound card installation cd I/O magic. It finds the driver stuff but will not complete because I keep getting message to insert ESS WDM driver disk. What is proper procedure to disable original sound card? Please help, this is driving me crazy!

12 replies

by maxwell edison

Greetings,

First, of corse, physically remove the old Sound Card. Go to Control Panel, System, Device Manager, Other Devices, and highlight the Sound Card. Click Remove. Go to add/remove programs and make sure that there are no sound card relatedprograms installed. If there are, uninstall them. Also, manually remove any folders uniquely associated with the old sound card.

Reboot the computer without any sound card at all.

Install the new Sound Card, reboot the computer, and let windows detect the new hardware. When you get to the part where Windows looks for and installs the driver, click om "have disk", and direct Windows to the disk/CD that came with the sound card.

Good luck,

Maxwell

by maxwell edison

.
.
I might add, when you are in the device manager, the sound card you have may be in a category by itself, such as Sound, Video and Game controller. But I'm sure you'll find it.

Regards,

Maxwell

by deliana

I have tried everything you suggested and still can't get sound. I even had a tech come to try to get things working properly. I think I may have to accept the fact that this computer for whatever reason will not have sound.

by fossil

at bootup, try going into the BIOS setup. there's often a "DISABLE ON_BOARD SOUND" chioice. once you do that, let the boot finish, then shut down. next time around you hsould be golden

by tjc

On my compaq presario 7453 I had to right click on my comtpuer go to properties, hardware profiles and then disabled the sound card from showing, since it was an onbord sound card.

I did also read that on some systems you have to do what I did but also disable it on some models though the BIOS.

Good luck - I got my self a SoundBlaster Gamer X 5.1, since my on board sound card kept turning off, and Compaq was no help with any of the fixes and such they suggested.

by fossil

I really feel the problem is with the settings for your BIOS. This is NOT connect in any way with Win2000. It is part of the hardware. THe full manual with instructions for doing this is at:
http://www.compaq.com/athome/support/msgs/7300/index.html
Click on the link. IT will let you download the ref. manual in a ZIP file with HTML docs. Once you have it unzip the file. For starters, look at CONFIG>HETM. It will tell you,"To change the system configuration, which is sometimes necessary when you add or remove optional hardware". You can find the same information at http://www.compaq.com/athome/support/msgs/7300/config.html . It will instruct you in creating a COmpaq Utilities Diskette. That, inturn, will let you change the necessary settings. If you feel uncomforatble doing this, go back to where you bought the sound card and pay another $50 to have them do the install/setup.

by maxwell edison

Greetings (again),

Fossil could be right about a setting in you BIOS. If there is on-board sound capability, the settings have to be just right.

In addition, however, when there is on-board sound, there's usually a jumper on the motherboard with several different setting options as well. The jumpers have to be set correctly. Your manual should explain it fully. (Even the downloaded manual).

Good luck,

Maxwell

This discussion is closed to new replies.